Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

High-power 0.4-mJ picosecond CPA system based on an extra-large-mode-area triple-clad fiber

A large dispersion-managed monolithic all-fiber chirped pulse amplification system for high-energy femtosecond laser generation

396 MHz CPA femtosecond laser system based on a single crystal fiber rod-type amplifier

Hybrid CPA system comprised by fiber-silicate glass fiber-single crystal fiber with femtosecond laser power more than 90 W at 1 MHz

Old Wavelength, New Performance: Hectowatt 200-μJ-level Femtosecond fiber CPA System at 1064 Nm

1720nm-1800nm tunable chirped pulse amplification based on thulium-doped fiber

Wavelength-Tunable Chirped Pulse Amplification System (1720 nm–1800 nm) Based on Thulium-Doped Fiber

10-µJ-level femtosecond pulse generation in the erbium CPA fiber source with microstructured hollow-core fiber assisted delivery and nonlinear frequency conversion

High-power, 474 Fs, 31.12 MHz, All-Polarization-maintaining, 1560 Nm Fiber Laser System Based on the Chirped-Pulse Amplification

High-power chirped pulse amplification based on Yb-doped rod-type PCF and nonlinear amplifying loop mirror oscillator

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier

Picosecond Laser System with 30-W Average Power Via Cavity Dumping and Amplifying

Tapered active fiber simultaneously enabled 141 W high average and 1.3 MW high peak power via all-fiber and polarization-maintained picosecond amplifier

Hybrid fiber-single crystal fiber chirped-pulse amplification system emitting more than 1.5 GW peak power with beam quality better than 1.3

High pulse energy, narrow-linewidth all-fiber 1064 nm picosecond master oscillator power amplifier system

100 MW Peak Power Picosecond Laser Based on Hybrid End-Pumped Nd:YVO4 and Side-Pumped Nd:YAG Amplifiers

112-Μj 180-Fs Pulses at 1-Khz Repetition Rate from Yb-Doped Laser Based on Strictly All-Fiber CPA Structure

Picosecond Yb-doped tapered fiber laser system with 1.26 MW peak power and 200 W average output power

High energy (> 40 nJ), sub-100 fs, 950 nm laser for two-photon microscopy

High-contrast 1.16 PW Ti:sapphire laser system combined with a doubled chirped-pulse amplification scheme and a femtosecond optical-parametric amplifier

Sub-60-fs, Compact 1100-Nm Fiber Laser System Based on Double-Pass Pre-Chirp Managed Amplification.