Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

Picosecond Laser System with 30-W Average Power Via Cavity Dumping and Amplifying

A Cavity-Dumped and Regenerative Amplifier System for Generating High-Energy, High-Repetition-rate Picosecond Pulses

High-power 0.4-mJ picosecond CPA system based on an extra-large-mode-area triple-clad fiber

A Sub-Picosecond Laser System Based on High-Energy Yb:YAG Chirped-Pulse Regenerative Amplification

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier

100 MW Peak Power Picosecond Laser Based on Hybrid End-Pumped Nd:YVO4 and Side-Pumped Nd:YAG Amplifiers

High Peak Power Picosecond Hybrid Fiber and Solid-State Amplifier System

Picosecond Nd:YLF Five-Passes Laser Amplifier with 20 Mj Pulse Energy

Nanosecond-pulse High-Peak-power Circle-Focusing Laser Beam for Laser Processing

High pulse energy, narrow-linewidth all-fiber 1064 nm picosecond master oscillator power amplifier system

1.2 MW peak power, all-solid-state picosecond laser with a microchip laser seed and a high gain single-passing bounce geometry amplifier

A New Type Of Diode-Pumped Cavity-Dumping Laser

396 MHz CPA femtosecond laser system based on a single crystal fiber rod-type amplifier

Picosecond-pulse amplification with an external passive optical cavity.

339 J High-Energy Ti:sapphire Chirped-Pulse Amplifier for 10 PW Laser Facility.

500 Hz, 47.1 Mj, Sub-Nanosecond MOPA Laser System

1 Mj, 500 Khz Nd:YAG/Nd:YVO4 MOPA Laser with a Nd:YAG Cavity-Dumping Seed Laser

100 Khz, 31 Ns, 189 J Cavity-Dumped Burst-Mode Nd:YAG MOPA Laser

High peak power 4.7 ns electro-optic cavity dumped TEM00 1342-nm Nd: YVO4 laser

100 kHz, 3.1 ns, 1.89 J cavity-dumped burst-mode Nd:YAG MOPA laser.

Research on a Cavity-dumped Burst-mode Laser and the Dual-stage Dual-pass Amplification