Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

100 MW Peak Power Picosecond Laser Based on Hybrid End-Pumped Nd:YVO4 and Side-Pumped Nd:YAG Amplifiers

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

High Peak Power Picosecond Hybrid Fiber and Solid-State Amplifier System

High Peak Power and High Beam Quality Fiber-Solid Hybrid Amplification Laser System

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier

Picosecond Yb-doped tapered fiber laser system with 1.26 MW peak power and 200 W average output power

72-Kw High-Peak-power Linearly-Polarized Single-Mode Pulsed Fiber Laser with 80 Khz Repetition Rate and 4.5 Ns Duration

High Energy (100 Mj) and High Peak Power (8 MW) Nanosecond Pulses Delivered by Fiber Lasers and Self-Focusing Analysis Based on a Novel Mode Decomposition Method

Laser Diode End-Pumped Nd:Yvo4 Regenerative Amplifier for Picosecond Pulses

Picosecond Nd:YLF Five-Passes Laser Amplifier with 20 Mj Pulse Energy

Hundreds of picosecond pulses amplifier based on Yb-doped tapered fiber for the generation of 100 W average output power

High energy single-frequency double-pulse hybrid MOPA system

1.2 kW, 20 kHz Nanosecond Nd:YAG Slab Laser System

Femtosecond Yb-doped Tapered Fiber Pulse Amplifiers with Peak Power of over Hundred Megawatts

High Peak Power Hybrid Mopa Laser With Tunable Pulse Repetition Frequency And Pulse Duration

Amplification and frequency quadrupling of picosecond long duration burst-mode laser

Hundred Watt Level and High Energy Compact Hybrid Fiber Femtosecond Laser with Good Beam Quality

High-power 0.4-mJ picosecond CPA system based on an extra-large-mode-area triple-clad fiber

100 Khz, 31 Ns, 189 J Cavity-Dumped Burst-Mode Nd:YAG MOPA Laser

1.2 MW peak power, all-solid-state picosecond laser with a microchip laser seed and a high gain single-passing bounce geometry amplifier

High-Peak-Power, High-Repetition-Rate Ld End-Pumped Nd:Yvo4 Burst Mode Laser