Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

Sub-50 fs pulses generation from an all-fiber monolithic gain-managed nonlinear amplifier with CFBG-based pre-compressor

Vector-dispersion Compensation and Pulse Pedestal Cancellation in a Femtosecond Nonlinear Amplification Fiber Laser System.

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Generation of ultrafast laser with 11 MW peak power from a gain-managed nonlinear tapered fiber amplifier

Sub-60-fs, Compact 1100-Nm Fiber Laser System Based on Double-Pass Pre-Chirp Managed Amplification.

Generation of 8-fs and 13-nJ pulse from a Yb-fiber system with nonlinear-pulse-compression

High-Power GHz Burst-Mode All-Fiber Laser System with Sub 300 fs Pulse Duration

Generation of sub-30 fs pulses from an erbium-doped fiber amplifier at 203 MHz repetition rate

All-fiber GHz few-cycle pulse generation at 2 µm

Compact, repetition rate locked all-PM fiber femtosecond laser system based on low noise figure-9 Er:fiber laser

A compact 51.6-W, 26- μ J, Yb-doped all-fiber integrated CPA system through quasi-rectangular pulse pre-shaping

Environmentally-stable 50-Fs Pulse Generation Directly from an Er:fiber Oscillator

Investigations of the High-Power, Single-Frequency, Sub-Microseconds, 1548-nm Fiber Laser Based on the Optical Pulse Modulation

396 MHz CPA femtosecond laser system based on a single crystal fiber rod-type amplifier

Cascaded nonlinear optical gain modulation for coherent femtosecond pulse generation

Sub-350 fs Pulse Generation via Nonlinear Compression With an Nd-Doped Picosecond Laser

Generation of a 59 Fs Pulse with a 550 Nm Spectral Range in a Mode-Locked Er-doped Single-Mode Fiber Laser System

Multifunctional all-fiber polarization-maintaining nonlinear pulse amplifier

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier

Nonlinear ultrafast fiber amplifiers beyond the gain-narrowing limit

Microjoule Level Femtosecond Optical Pulses with Double-Cladding Fiber-Based Nonlinear Chirped-Pulse Amplification