Abstract:Future compact integration of microwave modules will require intermetallic bonding with pitch connections lower than 10 μm. Solid-liquid interdiffusion (SLID) bonding is a potential bonding method for close heterogeneous integration because of its bonding temperature in the range of solder bonding, its ability to withstand higher temperaturs than bonding and its moderate compatibility with the joining of rough surfaces. This paper presents the results of an investigation of the Au—Sn system for integration of A3B5 chips on wafer level using SLID bonding. A sequence of five layers of Au and Sn with weight ratios of about 3:2 was deposited on a sapphire substrate. The structure and phases of the obtained system were investigated before and after annealing. The initial system has five distinctive alternating layers with an overall thickness of around 4.5 μm. After heat treatment at 320 °C with a holding time of 10 minutes, the Au—Sn system transforms into one layer that consists of only one phase ζ (Au0.853Sn0.147). The homogenization process is completed in less than 10 minutes. The ζ phase, of which the system is composed after annealing, has a melting point of 522 °C, which ensures the high temperature stability of the bonding layer. Bonding using the formed system was conducted. Morphology, elemental composition, and the initial mechanical properties of bonded structures have been studied. There are two types of defects in the joint's cross section: voids and the presence of local interfaces between two surfaces (an unbonded-like line). EDX analysis of the cross section of the joint between two crystals shows that the average ratio of Sn to Au over the cross section of the joint is 10.7 %. The complex of studies conducted suggests that the bonding area mostly includes the ζ phase, which will provide the best mechanical strength characteristics among the phases with a high Au concentration. The average bond shear strength is 32 MPa. Initial robustness results of the bonding are promising for space applications.

Low Temperature Fine Pitch Au-In Solid Liquid Inter Diffusion Bonding for Wafer Level Packaging

Low temperature solid-state-diffusion bonding for fine-pitch Cu/Sn/Cu interconnect

Low Temperature and Short Time Au/Sn Solid-liquid Diffusion Bonding for 3D Integration

Solid-State-Diffusion Bonding for Wafer-Level Fine-Pitch Cu/Sn/Cu Interconnect in 3-D Integration

Low Temperature Fine-Pitch Wafer-Level Cu-Cu Bonding Using Nanoparticles Fabricated by PVD

Low Temperature Au-In-Au Metallic Bonding and Its Application in the Fabrication of Vcsels

Low-Temperature Ultrasonic Bonding of Cu/Sn Microbumps with Au Layer for High Density Interconnection Applications

Wafer-Level Au—Sn Solid-Liquid Interdiffusion Bonding for Microwave Applications

Low-temperature wafer-level bonding with cu-Sn-in solid liquid Interdiffusion for microsystem packaging

Low Temperature Au/Sn Solid-Liquid Diffusion Chip-to-Chip Bonding for MEMS Encapsulation

Low Temperature Fine-pitch Cu-Cu Bonding Using Au Nanoparticles As Intermediate

Low Temperature Cu-Sn Bonding By Isothermal Solidification Technology

Recent Developments in Low Temperature Wafer Level Metal Bonding for Heterogenous Integration

Low Temperature Al Based Wafer Bonding Using Sn As Intermediate Layer

A Method for Fast Au-Sn Bonding at Low Temperature Using Thermal Gradient

A low-temperature bonding method for high power device packaging based on In-infiltrated nanoporous Cu

A Ag-Sn Isothermal Solidification Technology For Fluxless Hermetic Wafer Bonding

Metallurgical aspects and joint properties of Cu-Ni-In-Cu fine-pitch interconnects for 3D integration

Low-Temperature Cu–Cu Direct Bonding Using Pillar–Concave Structure in Advanced 3-D Heterogeneous Integration

Ultrasonic-enhanced silver‐indium transient liquid phase bonding in advancing rapid and low-temperature packaging

Research on Au/Au micro-bump bonding for millimeter wave frequencies heterogeneous integration