Abstract:Wafer bonding technology is important for most MEMS devices' packaging, especially for RF-MEMS devices. Different materials systems, such as Au-Sn, Au-In, have been developed for wafer bonding. A new bonding system, using Ag-Sn, is investigated in this paper. Comparing to well developed Au-Sn bonding (typically bonding temperature of 280degC ), Ag-Sn would provide a potentially lower temperature, lower cost wafer-level bonding method. Both cap wafer and bottom wafer were sputtered with thin film Ti/Ni. Ti is the adhesion layer, and Ni is the wettability and barrier layer. Sn/Au was evaporated on Ti/Ni for cap wafer. The cap wafer was patterned by lift-off process. Ag was sputtered on Ti/Ni for bottom wafer. The thickness of Sn and Ag was designed based on the composition ratio of Ag3Sn in the bonding layer. Thin Au film could protect Sn from oxidation. Afterwards the cap wafer and substrate wafer were brought into contact and sent into the bonding machine. Bonding process was performed in a nitrogen environment. Different bonding parameters such as bonding force, bonding temperature, dwell time are studied. During bonding, the Sn melted when the temperature reached the melting point of Sn and the liquid Sn broke up the barrier layer of the intermetallic compound of Au and Sn. Then the liquid Sn wetted and dissolved the Ag layer to form the intermetallic compound Ag3Sn. The growth of such an interfacial Ag3Sn intermetallic compound is a liquid-solid diffusion process. The main compositions of the bonding interface are pure Ag and Ag3Sn intermetallic compound, which was investigated by SEM and ED AX. Shear strength of the as-bonded structure and those after reliability tests were measured by a shear force tester. The reliability tests include pressure cooker test (PCT) and thermal cycling test (TCT). It has been concluded that the Ag- Sn bonding with delicately designed bonding process one of the potential methods for wafer- bonding.

Low Temperature Cu-Sn Bonding By Isothermal Solidification Technology

Mechanism and Process of Cu-Sn Bonding for Wafer Level MEMS Packaging

Low-temperature wafer-level bonding with cu-Sn-in solid liquid Interdiffusion for microsystem packaging

A Ag-Sn Isothermal Solidification Technology For Fluxless Hermetic Wafer Bonding

Experimental and computational investigation of low temperature Cu-Sn solid-state-diffusion bonding for 3D integration

Low Temperature Al Based Wafer Bonding Using Sn As Intermediate Layer

Solid-State-Diffusion Bonding for Wafer-Level Fine-Pitch Cu/Sn/Cu Interconnect in 3-D Integration

Low Temperature Cu-Cu Bonding Using an Intermediate Sacrificial Sn Layer

Low temperature solid-state-diffusion bonding for fine-pitch Cu/Sn/Cu interconnect

Low Temperature and Short Time Au/Sn Solid-liquid Diffusion Bonding for 3D Integration

High-Temperature Stable Au–Sn and Cu–Sn Interconnects for 3D Stacked Applications

Fast low-temperature–pressure Cu-Sn mechanical interlock bonding (MIB) applied for 3D integration

Ag-Sn Fluxless Wafer Bonding Technology

Low-Temperature Transient Liquid Phase Bonding Technology via Cu Porous-Sn58Bi Solid–Liquid System under Formic Acid Atmosphere

Wafer-Level Hermetic Package by Low-Temperature Cu/Sn TLP Bonding with Optimized Sn Thickness

An Insertion-Based Mechanical Interlock Cu-Sn Bonding Structure for Three-Dimensional Integration

Low Temperature Au/Sn Solid-Liquid Diffusion Chip-to-Chip Bonding for MEMS Encapsulation

Fabrication of Sn-plated Cu foam for high-efficiency transient-liquid-phase bonding

Interfacial Reaction and Mechanical Properties for Cu/Sn/Ag System Low Temperature Transient Liquid Phase Bonding

Cu-Based Thermocompression Bonding and Cu/Dielectric Hybrid Bonding for Three-Dimensional Integrated Circuits (3D ICs) Application

Electroless Silver Coating on Copper Microcones for Low-Temperature Solid-State Bonding