Abstract:Ni–Cu under-bump metallisation (UBM) can reduce stress and improve wetting ability in technology for electronic packaging technology advances with three-dimensional integrated circuit (3D IC) devices. The bond between the Sn-based solder and Ni–Cu UBM is affected by the formation of intermetallic compounds (IMCs), specifically Ni3Sn4 and (Ni,Cu)3Sn4. This paper investigates the mechanical properties of IMCs, which are critical in assessing the longevity of solder joints. First-principles calculations were carried out to investigate the phase stability, mechanical properties and electronic structures of Ni3Sn4, Ni2.5Cu0.5Sn4, Ni2.0Cu1.0Sn4, and Ni1.5Cu1.5Sn4 IMCs. The calculated formation enthalpies show that the doping of Cu atoms leads to a decrease in the stability of the phases and a reduction in the mechanical properties of the Ni3Sn4 crystal structure. As the concentration of Cu atoms in the Ni3Sn4 cells increases, the bulk modulus values of (Ni,Cu)3Sn4 formed with different compositions decrease from 107.78 GPa to 87.84 GPa, the shear modulus decreases from 56.64 GPa to 45.08 GPa, and the elastic modulus decreases from 144.59 GPa to 115.48 GPa, indicating that the doping of Cu atoms into the Ni3Sn4 cells may adversely affect their mechanical properties and increase the possibility of microcracking at the interface during actual service. The anisotropy of (Ni,Cu)3Sn4 is more significant than that of Ni3Sn4, with Ni2.0Cu1.0Sn4 showing the highest anisotropy. After evaluating the electronic structures, the metallic properties of Ni3Sn4 and the Ni2.5Cu0.5Sn4, Ni2.0Cu1.0Sn4, and Ni1.5Cu1.5Sn4 phases are revealed by electronic structure analysis. The total density of states (TDOS) for (Ni,Cu)3Sn4 structures is mainly influenced by Ni-d and Cu-d states. The addition of Cu atoms can increase the brittleness of Ni3Sn4. In addition, the region where d and p hybridisation occurs gradually increases with increasing Cu content. The electronic properties suggest that the binding energy between Ni and Sn atoms weakens with the addition of Cu atoms, resulting in a decrease in the elastic modulus. This research can serve as a valuable reference and theoretical guide for future applications of these materials.

Metallurgical aspects and joint properties of Cu-Ni-In-Cu fine-pitch interconnects for 3D integration

Novel Cu-nanowire-based technology enabling fine pitch interconnects for 2.5D/3D Integration

Low temperature solid-state-diffusion bonding for fine-pitch Cu/Sn/Cu interconnect

Microstructural evolution of Cu–Sn–Ni compounds in full intermetallic micro-joint and in situ micro-bending test

Experimental and computational investigation of low temperature Cu-Sn solid-state-diffusion bonding for 3D integration

Effects of Bonding Parameters on the Reliability of Fine-Pitch Cu/Ni/SnAg Micro-Bump Chip-to-Chip Interconnection for Three-Dimensional Chip Stacking

A Cu/Ni/Cu/Sn1.8Ag Microbump Structure for Void-free Interface under Long Time High-Temperature Storage

An Insertion-Based Mechanical Interlock Cu-Sn Bonding Structure for Three-Dimensional Integration

Solid-State-Diffusion Bonding for Wafer-Level Fine-Pitch Cu/Sn/Cu Interconnect in 3-D Integration

Low Temperature Fine-Pitch Wafer-Level Cu-Cu Bonding Using Nanoparticles Fabricated by PVD

High-Temperature Stable Au–Sn and Cu–Sn Interconnects for 3D Stacked Applications

Rapid formation, grain refinement and shear property of high-temperature-stable full IMC joints

Electromigration Reliability of Cu3Sn Microbumps for 3D Heterogeneous Integration

Development of low temperature Cu Cu bonding and hybrid bonding for three-dimensional integrated circuits (3D IC)

First-Principles Study of Cu Addition on Mechanical Properties of Ni3Sn4-Based Intermetallic Compounds

A low-temperature bonding method for high power device packaging based on In-infiltrated nanoporous Cu

Mechanical Property Of Cu-Sn-Ni Intermetallics In The Full Intermetallic Micro-Joints Formed With Transient Liquid Phase Soldering

Thermal instability of nanocrystalline Cu enables Cu-Cu direct bonding in interconnects at low temperature

Study on the evolution of interfacial (Cu,Ni)6Sn5 and shear property of (111)Cu/Sn/Ni micro joints under isothermal and TG-bonding

Intermetallic compound evolution and mechanical properties of Cu/Sn58Bi/Cu 3D structures blended with B 4 C nanoparticles during isothermal aging

Interfacial Characterization of Low-Temperature Cu-to-Cu Direct Bonding with Chemical Mechanical Planarized Nanotwinned Cu Films