Abstract:We have developed a new sol-gel route to synthesise Al2O3-SiO2 composite aerogels with different alumina/silica (Al/Si) molar ratios using an inexpensive inorganic salt. The approach is straightforward, inexpensive, and it produces monolithic mesoporous material with high specific surface area heat-treated at elevated temperatures. The effects of different Al/Si molar ratios and calcination temperatures on the microstructures and properties of Al2O3-SiO2 composite aerogels are investigated in this study. Results show that SiO2 is essentially amorphous, while Al2O3 predominately exists as polycrystalline boehmite for the as-dried composite aerogels. With the increase of Al/Si molar ratios, the morphologies change from connected spheroidal particles to nanometer-sized fibrous particles and web-like microstructures with varying diameters. As the heat treatment temperature increases to 600 degrees C, structural transition from boehmite to gamma-Al2O3 occurs within all the composite aerogels, and mullitization firstly occurs with the Al/Si molar ratio of 1 at around 1000 degrees C. The specific surface area undergoes an increase-decrease-increase process at 600 degrees C and 1200 degrees C for the composite aerogels with different Al/Si molar ratios. The specific surface area is as high as 166 m(2) g(-1) at 1200 degrees C for the sample with an Al/Si molar ratio of 8, which is higher than ever reported. The thermal conductivities of mullite fiber mat reinforced aerogel composites at room temperatures are 0.023 W m(-1) K-1, 0.029 W m(-1) K-1 and 0.025 W m(-1) K-1 with the Al/Si molar ratios of 2, 3 and 8, respectively, suitable for efficient thermal insulations uses.

Preparation of Heat-Resistant Silica/Alumina Composite Aerogel by Adding Trimethylethoxysilane

Synthesis and characterization of SiO2-Al2O3 composite aerogel using inorganic aluminum salt as raw material

Preparation of High-Temperature Resistant Aerogels by Incorporating Aluminum Sol into Composite Silica Sources Using Ambient Pressure Drying

Preparation and Characterization of Alumina-coated Hollow Quartz Fiber Reinforced Al2O3-SiO2 Aerogel Composite

Novel Al2O3–SiO2 composite aerogels with high specific surface area at elevated temperatures with different alumina/silica molar ratios prepared by a non-alkoxide sol–gel method

Synthesis of Al2O3-SiO2 aerogels with low thermal conductivity and high strength by methyltriethoxysilane as a silica precursor

Fabrication of Al2O3 aerogel-SiO2 fiber composite with enhanced thermal insulation and high heat resistance

Alumina-Doped Silica Aerogels for High-Temperature Thermal Insulation

Preparation of Alumina Aerogel via Supercritical Method

Synthesis of a novel Al 2 O 3 –SiO 2 composite aerogel with high specific surface area at elevated temperatures using inexpensive inorganic salt of aluminum

Novel silica-modified boehmite aerogels and fiber-reinforced insulation composites with ultra-high thermal stability and low thermal conductivity

Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

A Facile Method to Fabricate Al2O3-SiO2 Aerogels with Low Shrinkage up to 1200 °C

Highly thermally stable zirconia/silica composite aerogels prepared by supercritical deposition

Preparation and Characterization of Hydrophobic Mesoporous SiO2 Aerogel

Preparation and Characterization of C/Al 2 O 3 Composite Aerogel with High Compressive Strength and Low Thermal Conductivity

Synthesis of high temperature resistant ZrO2-SiO2 composite aerogels via “thiol-ene” click reaction

Fabrication and Thermal Stability of La2O3 Doped Alumina Aerogel

Design and preparation of novel Y2O3-SiO2 composite aerogels for high-temperature thermal insulators

Highly Thermally Stable Alumina-Based Aerogels Modified by Partially Hydrolyzed Aluminum Tri-Sec-butoxide

Preparation of monolithic Al2O3–SiO2 aerogels with high-temperature resistance using boehmite nanorods