Abstract:With the increasing severity in the service environment of secondary refining furnaces, traditional refractories cannot meet the high requirements. MgO-based fired refractories are subject to the thermal shock effect and slag penetration which are detrimental to their performance. In this study, low-carbon MgO-based refractories are reinforced by an in-situ MgAl2O4(MA)-TiO2 dense layer with the addition of low-cost self-prepared titanium carbonitride [Ti(C, N)]. The influence of the addition of as-prepared Ti(C, N) on the properties of low-carbon MgO-based refractories was investigated. The reinforced refractories had no cracks after 190 thermal shock cycles, demonstrating the highest hot modulus of rupture (HMOR) with excellent thermal shock resistance (TSR). After 2.5 h of rotary immersion in a steel slag, the corrosion depth of the composites was only 26.3% of that of commercial MgO-CaO refractories. Based on the thermodynamic analysis, the Ti(C, N) reinforcement mechanism for the low-carbon MgO-based refractories was studied. A MA-TiO2 dense layer formed during the oxidation process of the composites which enhanced the oxidation resistance. The volume expansion caused by the partial oxidation of Ti(C, N) prevents the penetration of the molten slag to refractories and Ti(C, N) powders forming a protective layer to further effectively protect the composites from slag corrosion owing to its high surface area. In addition, 3CaO·2TiO2 formed by the reaction between the steel slag and Ti(C, N) further increased the slag corrosion resistance (SCR) of the composites. This research offers a new idea for the material selection for secondary refining furnaces to achieve a green and effective steel-making production route and enriches the understanding of the phase behaviour in the Mg-Al-Ti-C-O-N system under high temperatures.

The Influence of MgO/ZrO2/Al2O3 Refractories on the Refining Process of Ti-containing Steel Based on Kinetic Study

Dynamic mass variation and multiphase interaction among steel, slag, lining refractory and nonmetallic inclusions: Laboratory experiments and mathematical prediction

Study on High‐Temperature Reactions of MgO Refractory with Ti‐Bearing Al‐Killed Steel

Development of a kinetic model for Ti‐bearing steel‐slag reaction

A thermodynamic model of the titanium distribution behaviour between slag and molten steel during LF refining process: description and application

Improved properties of in-situ MgAl2O4-TiO2 dense layer reinforced low-carbon MgO-based refractories

Steel/refractory/slag interfacial reaction and its effect on inclusions in high-Mn high-Al steel

Improving the Comprehensive Properties of ZrO2–C Materials with Aid of TiO2 Addition

Properties of various CaO-Al2O3-TiO2 refractories and their reaction behaviours in contact with Ti6Al4V melts

Kinetic study of control of alloy elements during electroslag remelting of Incoloy825

Dissolution Behavior of Mg and Ca from Dolomite Refractory into Al-killed Molten Steel

Simulation research on oxygen mass transfer between steel and slag in IF steel refining process

Revolution and Control of Fe-Al-(Mg, Ti)-O Oxide Inclusions in IF Steel during 260t BOF-RH-CC Process

Dissolution behavior of spent MgO–C refractory in the CaO–SiO2–FeO slag system as a steelmaking flux

Simultaneous recycling of Si and Ti from diamond wire saw silicon powder and Ti-bearing blast furnace slag via reduction smelting: An investigation of the effects of refractories on recycling

Reaction Mechanism between MgO and MgOC Lining Refractories and a High‐Carbon Al‐Killed Steel

Investigation on Viscosity and Nonisothermal Crystallization Behavior of P-Bearing Steelmaking Slags with Varying TiO2 Content

Influence of refining slag composition on nonmetallic inclusions in 38CrMoAl steel

Reaction mechanisms between slag and Ti(C,N)–MgAl2O3–Al2O3 refractories at 1600 °C

Dissolution Behavior of Mg from Magnesia-Chromite Refractory into Al-killed Molten Steel

Reaction mechanism between MgO crucible and AerMet100 steel during vacuum induction melting