Abstract:The refractory–slag–metal–inclusion multiphase reaction model was developed by integrating the refractory–slag, slag–metal, and metal–inclusion elementary reactions in order to predict the evolution of inclusions during the secondary refining processes. The mass transfer coefficient in the metal and slag phase, and the mass transfer coefficient of MgO in the slag were employed in the present multiphase reactions modeling. The “Effective Equilibrium Reaction Zone (EERZ) Model” was basically employed. In this model, the reaction zone volume per unit step for metal and slag phase, which is dependent on the ‘effective reaction zone depth’ in each phase, should be defined. Thus, we evaluated the effective reaction zone depth from the mass transfer coefficient in metal and slag phase at 1873 K (1600 °C) for the desulfurization reaction which was measured in the present study. Because the dissolution rate of MgO from the refractory to slag phase is one of the key factors affecting the slag composition, the mass transfer coefficient of MgO in the ladle slag was also experimentally determined. The calculated results for the variation of the composition of slag and molten steel as a function of reaction time were in good agreement with the experimental results. The MgAl2O4 spinel inclusion was observed at the early to middle stage of the reaction, whereas the liquid oxide inclusion was mainly observed at the final stage of the refining reaction. The content of CaO sharply increased, and the SiO2 content increased mildly with the increasing reaction time, while the content of Al2O3 in the inclusion drastically decreased. Even though there is slight difference between the calculated and measured results, the refractory–slag–metal multiphase reaction model constructed in the present study exhibited a good predictability of the inclusion evolution during ladle refining process.

Development of a kinetic model for Ti‐bearing steel‐slag reaction

A thermodynamic model of the titanium distribution behaviour between slag and molten steel during LF refining process: description and application

A thermodynamic model for predicting activity of CaO–SiO2–Al2O3–MgO–TiO2–V2O3–FeO slags during electric furnace smelting process

Kinetic study of control of alloy elements during electroslag remelting of Incoloy825

Effect of Al2O3 on the Molten Slag Microstructure Information by Molecular Dynamics Simulation and Experimental Analysis

Dynamic mass variation and multiphase interaction among steel, slag, lining refractory and nonmetallic inclusions: Laboratory experiments and mathematical prediction

Prediction Model for SiO2 Activity in the CaO-Al2O3-SiO2-MgO Quaternary Slag System

Mathematical model for design of optimized multi-component slag for electroslag remelting

Control of Aluminum and Titanium Contents in the Electroslag Remelting of ATI 718PlusTM Alloy

Thermodynamics on compositional design of slag for the Ti content control in bearing steel

Titanium Distribution Ratio Model of Ladle Furnace Slags for Tire Cord Steel Production Based on the Ion–Molecule Coexistence Theory at 1853 K

Refractory–Slag–Metal–Inclusion Multiphase Reactions Modeling Using Computational Thermodynamics: Kinetic Model for Prediction of Inclusion Evolution in Molten Steel

Simulation of Ladle Refining Reactions in Si–Mn‐Killed Steel

A coupled mathematical model and experimental validation of oxygen transport behavior in the electro-slag refining process

The development of a thermodynamic model for Al2O3–MgO refractory castable corrosion by secondary metallurgy steel ladle slags

Leaching Kinetics and Dissolution Model of Steel Slag in NaOH Solution

Study on the structural properties of refining slags by molecular dynamics with deep learning potential

Investigation on Viscosity and Nonisothermal Crystallization Behavior of P-Bearing Steelmaking Slags with Varying TiO2 Content

Solid reactions between CaO–Al2O3 and Si–Ti-containing steel at 1273 K

Study on the Melting Temperature of CaF2-CaO-MgO-Al2O3-TiO2 Slag under the Condition of a Fixed Ratio of Titanium and Aluminum in the Steel during the Electroslag Remelting Process

Modeling Viscosity of High Titania Slag