Abstract:Introduction Ge is one of the most promising channel materials to further improve the performance of Si CMOS due to its high hole and electron mobility [1-3]. In order to overcome the current Si FinFET technology, 3D channel structure is mandatory for Ge MOSFETs. To fabricate Ge Fins, CF4- or SF6-based RIE etching is usually employed for Ge etching [Ref. needed]. However, both CF4 and SF6 RIE etching results in large surface roughness which strongly degrades the performance of Ge FinFETs. On the other hand, it is necessary to realize high selectivity of anisotropic etching of Ge which is important to obtain superior static electrical control of Fin channel. In this research, we developed a SF6-CF4 cyclic RIE etching method for Ge Fin formation with suppressed surface roughness. The impact of inserting SF6-O2 etching steps into CF4-O2 etching process on the surface roughness of Ge was systematically investigated, as well as the ratio of vertical etching to horizontal etching of Ge. It is found that with a time proportion of 60% for SF6-O2etching steps, a minimum RMS of 1.1 nm is obtained for Ge Fin etching. Experiments The CF4-O2 and SF6-O2 RIE cyclic etching were carried out for (100) Ge surfaces with the same pressure, plasma power and total gas flow. Different time proportions of 0%, 20%, 40%, 60%, 80% and 100%, were used for SF6-O2 etching steps during the CF4-O2etching, with a total etching time of each cycle for 20 s. The selectivity of vertical and horizontal etching of Ge was examined using SEM, and the surface roughness of Ge after etching was evaluated using AFM. Results and discussion Figure 1 shows the etching rate of CF4-O2 and SF6-O2 cyclic etching with different time proportion of SF6-O2 step. It is observed that the etching rate significantly increases with increase of SF6-O2 etching proportion, due to the high reactivity of SF6 with Ge [4]. The RMS of Ge surfaces after CF4-O2 and SF6-O2 cyclic etching for 20 s is evaluated by AFM (Figure 2). It is confirmed that large amount of surface roughness is generated for Ge surface after both CF4-O2 and SF6-O2 etching. With introducing SF6-O2 etching steps into CF4-O2 etching, the surface roughness of Ge is obviously reduced. The RMS values of Ge surface after CF4-O2 and SF6-O2 cyclic etching are summarized in Figure 3 as a function of the time proportion of SF6-O2 etching. It is found that with a time proportion of 60% for the SF6-O2 step, a minimum RMS of 1.1 nm is obtained for the Ge surface. The impact of SF6-O2 proportion to the ratio of vertical and horizontal etching for Ge is also examined, as shown in Figure 3. It is found that the selectivity of vertical etching decreases with increasing the SF6-O2 proportion. However, a relatively high selectivity of vertical etching of over 4 is still maintained with a time proportion of 60% for SF6-O2etching, resulting in Ge Fins with superior morphology (Figure 4). Conclusion A CF4-O2 and SF6-O2 cyclic etching method is proposed for Ge Fin formation. It is found that with a time proportion of 60% for SF6-O2etching step, superior morphology is achieved for Ge Fins with sufficiently suppressed surface roughness of 1.1 nm. References [1] S. Takagi, et al. IEDM, 2003. [2] H. Shang, et al. IBM. J. Res. Dev., 2006. [3] K. C. Saraswat, et al., Microelectro. Eng., 2008. [4] A. Campo, et al. J. Vac. Sci. Technol. B, 1995.

Etching Silicon with Fluorine-Gas

Dry Etching of Silicon Materials in SF 6 Based Plasmas: Roles of and Gas Additives

The Lateral and Longitudinal Etching Rates of Silicon and Silica on Si(100) Surface

Reactive ion etching of SiC thin films using fluorinated gases

Molecular Dynamics Simulations of Influence of Surface Temperature on Fluorine Etching of Silicon

In-Flight Dry Etching of Plasma-Synthesized Silicon Nanocrystals

Orientation dependent etching of silicon by fluorine molecules: a quantum chemistry computational study

Molecular Dynamics Study of Interaction between Fluorine Atoms and Silicon Surface

Etching Mechanisms of CF3Etching Fluorinated Si: Molecular Dynamics Simulation

Molecular Dynamics Simulation of Lag Effect in Fluorine Plasma Etching Si

Modeling of fluorine-based high-density plasma etching of anisotropic silicon trenches with oxygen sidewall passivation

Reduction of RIE Induced Ge Surface Roughness by SF6-CF4 Cyclic Etching Method

Fluorine in Silicon: Diffusion, Trapping, and Precipitation

Selective etching of n-type silicon in pn junction structure in hydrofluoric acid and its application in silicon nanowire fabrication.

Inductively Coupled Plasma etching of amorphous silicon nanostructures over nanotopography using C4F8/SF6 chemistry

Reactive ion etching of plasma enhanced chemical vapor deposition amorphous silicon and silicon nitride: Feeding gas effects

Unexpectedly High Etching Rate of Highly Doped n-Type Crystalline Silicon in Hydrofluoric Acid

Direct Measurement of the Etching Rates on Si(111) and Silicon Dioxide Surfaces in 40% Ammonium Fluoride Aqueous Solution Via Atomic Force Microscopy

Fluorine‐containing species on the hydrofluoric acid etched silicon single‐crystal surface

High Aspect Ratio Si Etching Technique and Application

Etching of Si at low temperatures using a SF6 reactive ion beam: Effect of the ion energy and current density