Abstract:Introduction Ge is one of the most promising channel materials to further improve the performance of Si CMOS due to its high hole and electron mobility [1-3]. In order to overcome the current Si FinFET technology, 3D channel structure is mandatory for Ge MOSFETs. To fabricate Ge Fins, CF4- or SF6-based RIE etching is usually employed for Ge etching [Ref. needed]. However, both CF4 and SF6 RIE etching results in large surface roughness which strongly degrades the performance of Ge FinFETs. On the other hand, it is necessary to realize high selectivity of anisotropic etching of Ge which is important to obtain superior static electrical control of Fin channel. In this research, we developed a SF6-CF4 cyclic RIE etching method for Ge Fin formation with suppressed surface roughness. The impact of inserting SF6-O2 etching steps into CF4-O2 etching process on the surface roughness of Ge was systematically investigated, as well as the ratio of vertical etching to horizontal etching of Ge. It is found that with a time proportion of 60% for SF6-O2etching steps, a minimum RMS of 1.1 nm is obtained for Ge Fin etching. Experiments The CF4-O2 and SF6-O2 RIE cyclic etching were carried out for (100) Ge surfaces with the same pressure, plasma power and total gas flow. Different time proportions of 0%, 20%, 40%, 60%, 80% and 100%, were used for SF6-O2 etching steps during the CF4-O2etching, with a total etching time of each cycle for 20 s. The selectivity of vertical and horizontal etching of Ge was examined using SEM, and the surface roughness of Ge after etching was evaluated using AFM. Results and discussion Figure 1 shows the etching rate of CF4-O2 and SF6-O2 cyclic etching with different time proportion of SF6-O2 step. It is observed that the etching rate significantly increases with increase of SF6-O2 etching proportion, due to the high reactivity of SF6 with Ge [4]. The RMS of Ge surfaces after CF4-O2 and SF6-O2 cyclic etching for 20 s is evaluated by AFM (Figure 2). It is confirmed that large amount of surface roughness is generated for Ge surface after both CF4-O2 and SF6-O2 etching. With introducing SF6-O2 etching steps into CF4-O2 etching, the surface roughness of Ge is obviously reduced. The RMS values of Ge surface after CF4-O2 and SF6-O2 cyclic etching are summarized in Figure 3 as a function of the time proportion of SF6-O2 etching. It is found that with a time proportion of 60% for the SF6-O2 step, a minimum RMS of 1.1 nm is obtained for the Ge surface. The impact of SF6-O2 proportion to the ratio of vertical and horizontal etching for Ge is also examined, as shown in Figure 3. It is found that the selectivity of vertical etching decreases with increasing the SF6-O2 proportion. However, a relatively high selectivity of vertical etching of over 4 is still maintained with a time proportion of 60% for SF6-O2etching, resulting in Ge Fins with superior morphology (Figure 4). Conclusion A CF4-O2 and SF6-O2 cyclic etching method is proposed for Ge Fin formation. It is found that with a time proportion of 60% for SF6-O2etching step, superior morphology is achieved for Ge Fins with sufficiently suppressed surface roughness of 1.1 nm. References [1] S. Takagi, et al. IEDM, 2003. [2] H. Shang, et al. IBM. J. Res. Dev., 2006. [3] K. C. Saraswat, et al., Microelectro. Eng., 2008. [4] A. Campo, et al. J. Vac. Sci. Technol. B, 1995.

Etching Mechanisms of CF3Etching Fluorinated Si: Molecular Dynamics Simulation

Molecular Dynamics Study of Interaction between Fluorine Atoms and Silicon Surface

Molecular Dynamics Simulations of Influence of Surface Temperature on Fluorine Etching of Silicon

Orientation dependent etching of silicon by fluorine molecules: a quantum chemistry computational study

The Lateral and Longitudinal Etching Rates of Silicon and Silica on Si(100) Surface

Direct Measurement of the Etching Rates on Si(111) and Silicon Dioxide Surfaces in 40% Ammonium Fluoride Aqueous Solution Via Atomic Force Microscopy

Molecular Dynamics Simulation of Lag Effect in Fluorine Plasma Etching Si

Etching Silicon with Fluorine-Gas

Expression of the Si Etch Rate in a CF 4 Plasma with Four Internal Process Variables

Simulation of SiO2 etching in an inductively coupled CF4 plasma

Simulation of SiO<sub>2</sub> etching in an inductively coupled CF<sub>4</sub> plasma

Molecular Dynamics Simulation of Silicon Dioxide Etching by Hydrogen Fluoride Using the Reactive Force Field

Atomistic description of Si etching with HCl

Fluorine‐containing species on the hydrofluoric acid etched silicon single‐crystal surface

Molecular dynamics simulation of Si trench etching with SiO2 hard masks

Evidence for faster etching at the mask-substrate interface: atomistic simulation of complex cavities at the micron-/submicron-scale by the continuous cellular automaton

Reduction of RIE Induced Ge Surface Roughness by SF6-CF4 Cyclic Etching Method

Fluorine-Passivated Silicon Nanocrystals: Surface Chemistry Versus Quantum Confinement

Studies of atomic and molecular fluorine reactions on silicon surfaces

Reactive ion etching of SiC thin films using fluorinated gases

Synchrotron-Radiation-Induced Deposition of Etch-Protecting Film on Si in Cf4 Plasma