Abstract:Zirconia‐toughened alumina (ZTA) ceramics with high mechanical properties were sintered by hot‐pressing method using SiC particles (SiCp) and SiC whiskers (SiCw) as the reinforcing agents simultaneously. The influences of sintering temperature, SiCp and SiCw contents on the microstructure and mechanical properties of ZTA ceramics were investigated. It was found that both SiCp and SiCw could contribute to grain refinement significantly and promote the mechanical properties of the ceramics. However, the excess addition of SiCp or SiCw led to the formation of pores with large sizes and degraded the mechanical properties instead. When 13 wt% SiCp was introduced, the maximum flexural strength of 1180.0 MPa and fracture toughness of 15.9 MPa·m1/2 were obtained, whereas the maximum flexural strength of 1314.0 MPa and fracture toughness of 14.7 MPa·m1/2 were achieved at 20 wt% SiCw. Interestingly, the simultaneous addition of SiCp and SiCw could further improve the mechanical properties, and the highest flexural strength of 1334.0 MPa and fracture toughness of 16.0 MPa·m1/2 were achieved at a SiCw/SiCp ratio of 16/4. The reinforcement mechanisms in the ceramics mainly included the phase transformation toughening of ZrO2, the crack deflection and bridging of SiCp and SiCw and the pull‐out of SiCw.

Preparation of tough ÃÂ¡-SiAlON ceramics by spark plasma sintering with ÃÂ¢-Si3N4 as raw materials

Low-temperature Preparation of in Situ Toughened Yb Α-Sialon Ceramics by Spark Plasma Sintering (SPS) with Addition of Combustion Synthesized Seed Crystals

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Rapid Densification and Reaction Sequences in Self-Reinforced Y-α-SiAlON Ceramics with Barium Aluminosilicate As an Additive

Pressureless sintering of in-situ toughened Yb α-SiAlON ceramics by adding seed crystals prepared by combustion synthesis

Microstructure Characteristics And High-Temperature Performance Of In-Situ Reinforced Alpha-Sialon Ceramics

Thermal Shock Resistance of in Situ Toughened Α-Sialons with Barium Aluminosilicate As an Additive Sintered by SPS

Refractory self-reinforced Y-α-SiAlON with barium aluminosilicate glass ceramic addition

Mechanical properties and microstructure of laminated Si3N4+SiCw/BN+Al2O3 ceramics densified by spark plasma sintering

Fabrication of Yb alpha-SiAlON ceramics by SPS with crystal seeds prepared through combustion synthesis

Elongation Of Alpha-Sic Particles In Spark Plasma Sintered Alpha-Sialon/Alpha-Sic Composites

Combustion synthesis and sintering of rod-like Yb α-Sialon powders

Sintering Behavior, Microstructure and Mechanical Properties of Various Fluorine-Containing Y-SiAlON Glass-Ceramics

Combustion synthesis and sintering of rod-like Yb alpha-sialon powders

Investigation on Mechanical Properties of AlON Ceramics Synthesized by Spark Plasma Sintering

Fabrication of SiC whisker reinforced laminated Si3N4/BN ceramics by spark plasma sintering

Phase transformation and microstructure development of in situ toughened Yb α-SiAlON ceramics prepared by two-step hot-pressing

Sintering And Mechanical Properties Of Aln-Rich Ceramics In The Sic-Aln System

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Toughening and ablation mechanism of Si3N4 short fiber toughened ZrB2-based ceramics

Preparation of the Rod-Like Β-Si3n4 Particles Favoring the Self-Reinforcing Si3N4 Ceramics