Abstract:In this paper, TiC (1 wt%, 5 wt%, 10 wt%, 15 wt%)-reinforced TZM composites with high relative density and good mechanical properties were prepared by high energy ball milling and spark plasma sintering. The microstructure, element distribution, and phase composition of TZM-TiC composites were systematically analyzed and characterized. The mechanical properties of TZM-TiC composites were evaluated by microhardness test, room temperature compression test and high temperature compression test. The results proved that with the increase of TiC content, the size of Mo grains in TZM-TiC composites was significantly inhibited, and the morphology of the reinforcement phase changed from a spherical shape to a long stripe shape. Mo was found to be partially amorphous in TZM-TiC composites, and various second phases (TiC, Ti and Mo 2 C) were found in the TZM-TiC composites. Through two-dimensional mismatch theory and first-principle calculations, the strengthening effect of Mo-Mo 2 C interface was much higher than that of Mo-TiC and MoTi interface. The generation of amorphous Mo, the grain refinement and the second phase strengthening together significantly improve the micro-Vickers hardness and compressive strength of TZM-(10%, 15%)TiC composites, which contributes to the Vickers hardness of TZM-15%TiC reaching 885.77 HV, and the compressive yield strength of TZM-10%TiC composite reaching 2169.7 MPa. Besides, the TZM-10%TiC composite exhibits excellent thermal stability, and its compressive yield strength at 600 °C reaches 1880.7 MPa.

Microstructure and Performances of W–TiC–Y2O3 Composites Prepared by Mechano-Chemical and Wet-Chemical Methods

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Microstructure and Transient Laser Thermal Shock Behavior of W–TiC–Y2O3 Composites Prepared by Wet Chemical Method

Preparation and Properties of Fine-Grained and Ultrafine-Grained W-TiC-Y2O3 Composite

Investigation on microstructure and reinforcement mechanism of the TiC-reinforced W-matrix composite prepared by high-energy ball milling and spark plasma sintering

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

The Effect of Y2O3 Particles on the Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Tungsten Composites

Synthesis and Formation Mechanism of W/TiC Composite Powders by a Wet Chemical Route

Preparation and organization of W-Ni/TiC composite material

Microstructure and mechanical properties of TiC reinforced TZM composites prepared by spark plasma sintering

Excellent performance of W–Y2O3 composite via powder process improvement and Y2O3 refinement

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Influence of TiC Content on Microstructure and Properties of W-30Cu/TIC Composites

Preparation of TiC-doped W-Ti Alloy and Heat Flux Performance Test under Laser Beam Facility

Microstructure and mechanical properties of Wf/W composites influenced by Y2O3 coating

Preparation and Characteristics of W–1 Wt.% TiC Alloy Via a Novel Chemical Method and Spark Plasma Sintering

Microstructure and properties of Y2O3/Cu composites fabricated by a novel liquid phase in situ reactive synthesis process

Microstructure and Tribological Properties of WC/Ni-MoS2 Titanium-Based Composite Coating on TC4

Microstructure Evolutions of the W–TiC Composite Conducted by Dual-Effects from Thermal Shock and He-ion Irradiation