Abstract:Carbide dispersion strengthened W(CDS-W) has attracted much attention as a plasma-facing material (PFM). However, the carbide tends to segregate at W grain boundaries and has poor interface properties with W due to the large difference in the bond structure. In this work, nanometer Ti was added to improve the performance of the W/TiC interface, and nanoscaled W-TiC-x%Ti (x = 0.1,0.5 and 1.0) composites were prepared by chemicalmechanical milling and ordinary sintering method. The effects of Ti on powder morphology, phase composition, microstructure and mechanical properties were systematically investigated using XRD, SEM, EDS, TEM and HADDF technologies. Simultaneously, the existence form and distribution of Ti elements, and W/TiC interface characteristics of powders and composites were analyzed. Moreover, the microstructure evolution and strengthening mechanism were preliminarily discussed. Results show that the W-TiC/Ti powder has an obvious core-shell multilayer structure with a particle size range of 50-120 nm. The addition of Ti exists in the forms of TiC, Ti, and TiO2, and has no effect on the morphology and phase composition. Besides, the phase transformation and solution-precipitation of the Ti-added occurs during the sintering process. Part of Ti precipitates on the W/ TiC surface to form Ti rich region, which significantly promotes the dispersion of TiC and improves the W/TiC interface, as well as prevents the growth of W grains, and the average grain size is 2.90 mu m. Moreover, the orientation relationship of [013](2 00)TiCFCC||[1 13](11 0)WBCC exists at the W/TiC interface, especially the coherent phase interface is formed. The tensile strength and microhardness at room temperature are 520 MPa and 850 HV0.2, respectively, which is attributed to the synergistic effect of fine-grained strengthening, dispersion strengthening and interface strengthening. This work can provide a new strategy and direction for preparing high-performance CDS-W materials.

Preparation and organization of W-Ni/TiC composite material

Synthesis and Formation Mechanism of W/TiC Composite Powders by a Wet Chemical Route

Preparation and Sintering Performance of W-Ni/Yb2O3 Composite Materials

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

Influence of TiC Content on Microstructure and Properties of W-30Cu/TIC Composites

Activation Pretreatment of W-1.5wt％TiC Composite Powder and Its Sintering Behavior

Preparation and Properties of WC-TiC-Ni Cemented Carbide

The Microstructure and Mechanical Property of W-TiC/Ti Composites Via Chemical-Mechanical Milling Method

Preparation and Characteristics of W–1 Wt.% TiC Alloy Via a Novel Chemical Method and Spark Plasma Sintering

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy

Microstructure and Performances of W–TiC–Y2O3 Composites Prepared by Mechano-Chemical and Wet-Chemical Methods

Preparation and microstructure of Ni-coated TiC composite powder by electroless plating

Effect of Silver Element on Microstructure and Properties of W-30Cu/TiC Composites

Preparation of Nickel-Coated Titanium Carbide Particulates and Their Use in the Production of Reinforced Iron Matrix Composites

Synthesis of W-TiC composite powders by wet-chemical process and its sintering behavior by SPS

Effect of Doped Niobium on the Microstructure and Properties of W–Nb/TiC Composites Prepared by Spark Plasma Sintering

Preparation of Nickel-Coated Tungsten Carbide Powders by Room Temperature Ultrasonic-Assisted Electroless Plating

Microstructure and wear properties of Ni/TiB2-TiC composites prepared by spark plasma sintering

Preparation and properties of Ni-W-P-TiO2 nanocomposite coatings developed by a sol-enhanced electroplating method

Preparation and microstructure of nano-size cobalt-coated Al2O3/TiC composites

Preparation of W-10Ti alloy with tungsten powder of different sizes and TiH2 powder by liquid phase sintering