Abstract:Tungsten (W) is one of best candidate metal for plasma-facing materials (PFM), especially due to its high melting temperature and neutron absorption capability. However, converting W into bulk PFM is hard because of its high melting point. This problem can be solved by adding metallic sintering aids with low melting points. In this study, W matrix with 1 wt% Ni aid was reinforced by adding NdB6 particles (1, 5, and 10 wt%). It can be introduced as a novel potential PFM, thanks to its low volatility and high neutron absorbability. The ceramic and composite powders produced via mechanochemical synthesis and mechanical alloying were examined in terms of composition, particle size, crystallite size, and lattice strain. Samples sintered via pressureless sintering (PS) and spark plasma sintering (SPS) were microstructurally analyzed by using an X-ray diffractometer (XRD), a scanning electron microscope (SEM) attached with an energy dispersive spectroscope (EDS), and mechanically analyzed in terms of microhardness and wear behavior. Based on the results, W2B and WB phases emerged in the SPS'ed W1Ni-5NdB6 and PS'ed./SPS'ed W1Ni-10NdB6 composites. SPS'ed W1Ni-10NdB6 composite had the highest hardness value and the lowest specific wear rate. The SPS'ed W1Ni-5NdB6 composite showed fewer surface damages and higher irradiation resistance as compared with other samples after exposure of He+ irradiation.

Preparation and Sintering Performance of W-Ni/Yb2O3 Composite Materials

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Preparation and organization of W-Ni/TiC composite material

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy

Microstructure and mechanical properties of liquid–phase sintered W@NiFe composite powders

Preparation, Mechanical Properties and Wear Resistance of Ni–W/SiC Nanocomposite Coatings

Investigation on Microstructure and Tribological Performances of Electrodeposited Ni-W-Y2O3 Composite Coatings

Preparation and Performance of NiCuZn–Co2Y Composite Ferrite Material

Microstructure and Performances of W–TiC–Y2O3 Composites Prepared by Mechano-Chemical and Wet-Chemical Methods

Strong Cube Texture Formation of Ni5W/Ni9.3W/Ni5W Composite Thin Substrates for YBCO-coated Conductors

Effect of nickel content on the sintering behavior, mechanical and dielectric properties of Al2O3/Ni composites from coated powders

The Effect of Y2O3 Particles on the Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Tungsten Composites

Fabrication and Characterization of Tungsten Heavy Alloys with High W Content by Powder Metallurgy

Preparation and Properties of Fine-Grained and Ultrafine-Grained W-TiC-Y2O3 Composite

A Novel Plasma-Facing NdB6 Particulate Reinforced W1Ni Matrix Composite: Powder Metallurgical Fabrication, Microstructural and Mechanical Characterization

Excellent performance of W–Y2O3 composite via powder process improvement and Y2O3 refinement

Microstructure and Failure Mechanism of Y2O3 Coating on the W Fiber in Wf/W Composites During Field Assisted Sintering

Microstructure and mechanical properties of Wf/W composites influenced by Y2O3 coating

Effect of yttrium oxide addition on the microstructure and mechanical properties of WC–ni composites fabricated from recycled WC and Ni

Preparation and properties of Al2O3/Ni composite from NiAl2O4 spinel by in situ reaction sintering method