Abstract:Pure W with grain size of 1.77 μm, ultrafine-grained W-10wt.%Cr-2wt.%Ti (W-10 C-2 T) alloy with grain size of 161 nm and W-10wt.%Cr-4wt.%Ti (W-10 C-4 T) alloy with grain size of 148 nm, were prepared by mechanical alloying followed by hot isostatic pressing (HIP) sintering. Ultrafine-grained structure stability mechanisms of W-10 C-2 T and W-10 C-4 T can be mainly ascribed to the thermodynamic aspect illustrated by the kinetic calculation of critical maximum W grain size. The average grain size of W-10 C-4 T is smaller than that of W-10 C-2 T, and the increasing additional amount of Ti can further inhibits grain growth. The second phase particles can interact with free oxygen to purify and strengthen grain boundaries, and the faster thermal diffusion rate of Cr and Ti can improve the density of W-10 C-2 T and W-10 C-4 T alloys obviously, compared with pure W. The Vickers hardness of W-10 C-2 T and W-10 C-4 T alloys were tested, and results show that they possess ultrahigh hardness, the value of their Vickers hardness is 1237 ± 74 kgf/mm2 and 1402 ± 46 kgf/mm2, respectively, which is much larger than that of pure W and coarse-grained W-based alloys. The ultrahigh hardness comes from the abundant grain boundaries (GBs) that act as obstacles and potential barriers for dislocation motion, and second phase strengthening. High-temperature annealing treatment results show that W-10 C-2 T and W-10 C-4 T alloys possess excellent thermal stability at the annealing temperature of 1000 °C and 1100 °C, and the thermal stability mechanisms were explored.

Preparation and Properties of Fine-Grained and Ultrafine-Grained W-TiC-Y2O3 Composite

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Microstructure and Performances of W–TiC–Y2O3 Composites Prepared by Mechano-Chemical and Wet-Chemical Methods

The Effect of Y2O3 Particles on the Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Tungsten Composites

Excellent performance of W–Y2O3 composite via powder process improvement and Y2O3 refinement

The superior thermal stability and irradiation resistance capacities of tungsten composites synthesized by simple second-phase particle component modulation

Microstructure and mechanical properties of Wf/W composites influenced by Y2O3 coating

Microstructure and Transient Laser Thermal Shock Behavior of W–TiC–Y2O3 Composites Prepared by Wet Chemical Method

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Effect of Grain Refinement on the Comprehensive Mechanical Performance of W–Cu Composites

Microstructure and Failure Mechanism of Y2O3 Coating on the W Fiber in Wf/W Composites During Field Assisted Sintering

Synthesis of W-TiC composite powders by wet-chemical process and its sintering behavior by SPS

Investigation on microstructure and reinforcement mechanism of the TiC-reinforced W-matrix composite prepared by high-energy ball milling and spark plasma sintering

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

Preparation and Sintering Performance of W-Ni/Yb2O3 Composite Materials

Interfacial Microstructure and Mechanical Property of the Discontinuous Short Tungsten Fiber-Reinforced Tungsten Matrix Composites

Microstructures, mechanical properties, and oxidation behavior of in-situ ultra-fine duplex carbides reinforced Ni-based superalloy composites

Study of a New Method to Fabricate W–Cu Composites

Ultrafine-grained W-based alloys prepared by HIP with ultrahigh hardness and excellent thermal stability

Effect of sintering temperature on fine-grained Cu W composites with high copper

Tailoring Ultrafine Grained and Dispersion-Strengthened Ti2AlC/TiAl Composite Via a New Fabrication Route