Abstract:The effects of different ultrasonic vibration powers on the distribution, phase structure, friction and wear properties of WC reinforced particles in laser melted Ni60/WC composite coatings are investigated. The effects of ultrasonic vibration on the microstructure, elemental distribution, crystal orientation, friction and wear properties of the fused coatings are analyzed. The experimental results show that the deposition of WC particles in the lower and middle parts of the coating is significantly improved after the introduction of ultrasonic vibration during the fusion cladding process. In particular, at 600 W ultrasonic power, not only the distribution uniformity of tungsten carbide particles in the coating is optimal, but also the composite coating shows better wear resistance. However, too much ultrasonic power increases the possibility of particle agglomeration. In addition, although the phase pattern of the coating does not change after ultrasonic vibration, the width of the columnar crystalline region of the coating is reduced, and the coating is covered by a homogeneous lamellar nanoscale eutectic structure with the phase compositions of the γ-(Fe, Ni) and M 23 C 6 phases. The ultrasonic vibration improves elemental segregation of the coating, reduces the large number of precipitated phases in the coating, weakens the grain growth orientation, and relieves the local stress concentration in the coating. In addition, the mechanism of the influence of WC particles on the microstructure evolution and wear resistance of the composite coatings is discussed.

Microstructure and mechanical properties of Wf/W composites influenced by Y2O3 coating

Mechanical Properties and Thermal Shock Performance of W-Y2O3composite Prepared by High-Energy-rate Forging

Microstructure and Failure Mechanism of Y2O3 Coating on the W Fiber in Wf/W Composites During Field Assisted Sintering

The Effect of Y2O3 Particles on the Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Tungsten Composites

Interfacial Microstructure and Mechanical Property of the Discontinuous Short Tungsten Fiber-Reinforced Tungsten Matrix Composites

Excellent performance of W–Y2O3 composite via powder process improvement and Y2O3 refinement

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Effect of yttrium oxide addition on the microstructure and mechanical properties of WC–ni composites fabricated from recycled WC and Ni

Preparation and Properties of Fine-Grained and Ultrafine-Grained W-TiC-Y2O3 Composite

Microstructure and wear performance of a WC-8Co hard alloy modified using W powders doped with Y 2 O 3

Microstructure and wear performance of a WC-8Co hard alloy modified using W powders doped with Y<sub>2</sub>O<sub>3</sub>

Microstructural evolution and toughening mechanism of WC-Co composite prepared by amorphous-crystallization method

Synergistic effects of tungsten coating on the microstructure, thermophysical and mechanical properties of graphite flakes reinforced copper matrix composites

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Microstructure and Performances of W–TiC–Y2O3 Composites Prepared by Mechano-Chemical and Wet-Chemical Methods

Microstructure and mechanical property of high velocity oxy-fuel sprayed multimodal WC-Cr3C2–Co–Y2O3 cermet coating

Microstructure, Mechanical and Tribological Properties of WC-WCoB Coating

Microstructure and mechanical properties of 20Wf/30ZrCp/W composite

Effect of WC–Co addition on tribological and cracking behavior of laser cladded Fe-based amorphous/crystalline composite coatings

Influence of ultrasonic assistance on the microstructure and friction properties of laser cladded Ni60/WC composite coatings

The superior thermal stability and irradiation resistance capacities of tungsten composites synthesized by simple second-phase particle component modulation