Abstract:In this study, the effect of heat treatment and yttrium additions on the microstructure, mechanical properties, and tribological behavior of Al-15% Mg2Si cast composites was investigated. The microstructural study revealed the presence of both primary and secondary Mg2Si phases in all composite specimens and also Y-containing intermetallics (Al2Y phases) at higher concentrations. It was also found that Y addition does not change the size and morphology of primary Mg2Si particles considerably, but the pseudo-eutectic Mg2Si changed from a flake-like morphology to fine fibrous or rod-like one. The results show that proper content of Y additions can reduce the amount of Mg2Si phase through dissolving it into the matrix, lead to the precipitation of Al2Y phase and improve the mechanical properties. Modified composites with 0.5% Y exhibited an ultimate tensile strength (UTS) of 290 MPa with an elongation of 4.3%. After exposing the composite to solution treatment at 520 °C for 4 h, the tensile strength of the composite continuously increased with the increase of Y content, and reached the maximum at 1% Y. The maximum UTS and elongation at room temperature for the heat-treated composites are 294 MPa and 7.4%, respectively. In the cast specimen, fracture surfaces are covered by packets with coarse steps, suggesting a brittle mode of failure. Modified composites with 0.5 wt.% Y contain several cracked particles together with a few decohered primary Mg2Si particles. In solution heat-treated state, dimples present at the fracture surface are rather coarse but homogenous, showing a semi-ductile mode of fracture. Wear test results showed that the wear resistance of all specimens increases with the addition of Y up to 0.3 wt.%. Scanning electron microscopic observations of the worn surfaces revealed that the dominant wear mechanism was abrasive wear accompanied by some delamination wear mode.

Mechanical behavior of Y 2 O 3 -coated Al 2 O 3p /6061 Al composites

Microstructure and Tensile Properties of Yttria Coated-Alumina Particulates Reinforced Aluminum Matrix Composites

Effect of coating Al2O3 reinforcing particles on the interface and mechanical properties of 6061 alloy aluminium matrix composites

Effect of surface modification of Al2O3 powder with Y2O3 on microstructure and tensile properties of aluninium matrix composites

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF Y2O3 MODIFIED-Al2O3 PARTICLE /6061Al COMPOSITES

Rare-Earth Oxide Coating for Sub-Micro Particulates Reinforced Aluminum Matrix Composites

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF Y_2O_3 MODIFIED-Al_2O_3 PARTICLE /6061Al COMPOSITES

Coating of Y2O3 additive on Al2O3 powder and its effect on the wetting behaviour in the system Al2O3p/Al

Microstructure and interface analysis of rare-earth modified-Al2O3 particle/6061A1 composites

Effect of Surface Modification of Sub-Micron Al2O3 Particles by Rare-Earth on Interfacial Wettability of Al Matrix Composites

Microstructure and Properties of Al2O3-Y2O3 Ceramic Composite Coatings Fabricated by Plasma Spraying

Mechanical and Tribological Characterization of Al-Mg2Si Composites after Yttrium Addition and Heat Treatment

Preparation and Properties of ZrO2-Al2O3 Composite Ceramic Coatings on 6061 Aluminum Alloy Surface

Microstructure and wear resistance of plasma arc cladding Y2O3/cobalt-based alloy coating

Effect of Y2O3-stabilized ZrO2 Whiskers on the Microstructure, Mechanical and Wear Resistance Properties of Al2O3 Based Ceramic Composites

Surface modification and characterization of A12O3 micropowder

Microstructure and properties of Al2O3-ZrO2-Y2O3 coatings during high temperature and thermal shock resistance

Mechanical properties of the alumina-coated Al18B4O33w/6061Al composites

Microstructure and Tribocorrosion Behavior of Al2O3/Al Composite Coatings: Role of Al2O3 Addition

Microstructure and mechanical properties of Wf/W composites influenced by Y2O3 coating

Mechanical and Wear Properties of Al<sub>2</sub>O<sub>3</sub>-15wt%ZrO<sub>2</sub> Composites