Abstract:To extend the safety service life of aviation TC4 alloy, the composite coatings of TC4 + Ni-MoS2 + WC + xY2O3 (x = 0, 1, 2, 3, 4 wt.%) were prepared on TC4 by coaxial powder feeding laser cladding technology. The results showed that all the coatings had the same generated phases which mainly consisted of TiC, Ti2Ni, Ti2S, matrix β-Ti, and unfused residual WC. Y2O3 formed co-dependent growth relationships with TiC, Ti2S, and Ti2Ni. Meanwhile, TiC-Ti2S, TiC-Ti2Ni, and Ti2S-Ti2Ni coherent composite structure phases were effectively synthesized in all the coatings. With the increase in the Y2O3 content, the exposed area of the matrix increased and other phases refined progressively. When the Y2O3 content in the coatings were 3 and 4 wt.%, the degree of phase refinement in the coatings was consistent and the phases grew along grain boundaries, but microstructure segregated in the 4 wt.% Y2O3 coating. The microhardness of all the coatings was higher than that of TC4 and decreased with the increase in the Y2O3 content. Higher friction coefficients and lower wear rates both appeared in all the coatings than in the substrate, and they presented a trend of decreased first and then increased with the addition of Y2O3, in which the 3 wt.% Y2O3 coating had the lowest friction coefficient and optimal wear resistance. The research found that the Y2O3 could not change the types of phases in the coatings and could serve as a heterogeneous nucleation center for the refinement of the TiC-Ti2S-Ti2Ni coherent structure phase. Meanwhile, except for the matrix phase, Y2O3 could attract other phases to pinning on the grain boundaries of the coatings. The content of Y2O3 was negatively correlated with the hardness and wear resistance of the coating and it had the optimal tribological properties with the moderate amount of Y2O3. The wear mechanism of all coatings was abrasive wear.

Microstructure and wear performance of a WC-8Co hard alloy modified using W powders doped with Y 2 O 3

Microstructure and wear performance of a WC-8Co hard alloy modified using W powders doped with Y<sub>2</sub>O<sub>3</sub>

Change of interfacial structure between the matrix and second phase of Y–Zr-modified WC-8Co cemented carbide

Study on Elemental Composition and Interfacial Structure of the Second Phase in WC-8Co Hard Alloy Doped with Rare Earth Components

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Synthesis of Y2O3-doped WC-Co powders by wet chemical method and its effect on the properties of WC-Co cemented carbide alloy

Study on preparation and properties of WC-8Co cemented carbide doped with rare earth oxide

Microstructure, Mechanical and Tribological Properties of WC-WCoB Coating

Effect of W on the Mechanical Properties and Tribological Behavior of CoCrFeNiWx Compositionally Complex Alloy

Effect of Y2O3 on microstructure and mechanical properties of WC-Co-cemented carbides prepared via solid-liquid doping method and spark plasma sintering

Effects of Y2O3 Content on the Microstructure and Tribological Properties of WC-Reinforced Ti-Based Coatings on TC4 Surfaces

Microstructure and mechanical properties of Wf/W composites influenced by Y2O3 coating

Microstructure and wear resistance of bimodal cemented carbide coating prepared by direct laser powder deposition

Effect of Y2O3 Addition on the Microstructure, Wear Resistance, and Corrosion Behavior of W-4.9Ni-2.1Fe Heavy Alloy

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effect of WC addition on microstructure and properties of laser melting deposited Ti6Al4V

WC-Co Composite Coating Deposited by Cold Spraying of a Core-Shell-Structured WC-Co Powder

On the Enhanced Wear Resistance of Ultra-Coarse WC-Co Cemented Carbides by WCoB Addition

Effect Of Y2o3 On Friction And Wear Behavior Of W-4.9ni-2.1fe Alloy

Microstructure and mechanical property of high velocity oxy-fuel sprayed multimodal WC-Cr3C2–Co–Y2O3 cermet coating