Abstract:Oxide dispersion strengthened copper-based material is widely used in electrical contact materials due to its excellent mechanical and electrical properties. However, researchers have found that large Y 2 O 3 particles have poor interfacial bonding with the copper matrix in the study of oxide dispersion strengthened copper. In this work, Y 4 Zr 3 O 12 nanoparticles were successfully prepared through solid–liquid doping and directly added into oxide dispersion-strengthened copper by mechanical alloying. A scanning electron microscope, a transmission electron microscope, an X-ray diffractometer, and electrical and mechanical tests were used to characterize the microstructure and performance of composite materials. The interfaces between the Y 2 O 3 /Y 4 Zr 3 O 12 nanoparticles and Cu were systematically studied. The interface bonding between Y 4 Zr 3 O 12 and Cu was better than that of Y 2 O 3 and Cu. The effect of different Y 4 Zr 3 O 12 contents (1, 3, and 5 wt%) on the microstructure and mechanical properties of the composites was studied. Results showed that the Cu-3 wt% Y 4 Zr 3 O 12 composites exhibited the best comprehensive properties. The Vickers hardness, yield strength, ultimate tensile strength, maximum engineering strain, and electrical conductivity of the Cu-3 wt% Y 4 Zr 3 O 12 composites were 132HV, 203.5 MPa, 284.7 MPa, 15.8 %, and 90.3 % International Annealed Copper Standard, respectively.

Microstructure and properties of Y2O3/Cu composites fabricated by a novel liquid phase in situ reactive synthesis process

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Effect of nano-Y2O3 on the microstructure and mechanical properties of Cu-10W composites prepared by spark plasma sintering

Multiphase strengthening mechanism of Cu-Y2O3/W composites prepared by mechanical alloying

Effects of solid–liquid doping and spark plasma sintering on the microstructure and mechanical properties of Y2O3-doped copper matrix composites

Effect of alloying element Zr on microstructure and properties of Cu−Y2O3 composites

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis

Investigation on Microstructure and Properties of Cu–Al2O3 Composites Fabricated by a Novel In-Situ Reactive Synthesis

Paper Presented at the 2 Nd Sino-German Symposium on Computational Thermodynamics and Kinetics and Their Applications to Solidification

Microstructure, Mechanical and Oxidation Properties of In-Situ Synthesized (y2o3 + Tic)/Ti-4.5si Composites

Microstructure Evolution and Properties of an In-Situ Nano-Gd2O3/Cu Composite by Powder Metallurgy

Development of Y2O3 Dispersion-Strengthened Copper Alloy by Sol-Gel Method

Excellent performance of W–Y2O3 composite via powder process improvement and Y2O3 refinement

Microstructure and mechanical properties of Y2O3 reinforced Ti6Al4V composites fabricated by spark plasma sintering

Microstructure Characterization of the Cu-Ti-C Composites Prepared by Mechanical Alloying and Spark Plasma Sintering

Effects of composite oxide addition on the microstructure and properties of ODS copper

The Effect of Y2O3 Particles on the Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Tungsten Composites

Effect of Y Precursors on the Synthesis of Cu-Y2o3 by Mechanical Alloying and Spark Plasma Sintering

Microstructure and Performances of W–TiC–Y2O3 Composites Prepared by Mechano-Chemical and Wet-Chemical Methods

Microstructure and electrical contact behavior of Al<sub>2</sub>O<sub>3</sub>-Cu/30W3SiC(0.5Y<sub>2</sub>O<sub>3</sub>) composites

Microstructure, Mechanical and Tribological Properties of Oxide Dispersion Strengthened High-Entropy Alloys.