Abstract:The prevention of hot cracking formation is of utmost importance in the production of the new Ni-Co based superalloys through the utilization of the electron beam smelting layered solidification technique (EBSL), as it ensures exceptional homogeneity and dependable consistency of the specimens. In contrast to previous studies that focused on minimizing the liquid film and solidification range, our methodology adopts a distinct approach. In this research, a novel methodology was employed to mitigate internal stresses through the implementation of equiaxed grain layers via an alternately reduced cooling method. This ultimately resulted in the elimination of hot cracking. To be more specific, the transition from a columnar to an equiaxed structure was observed during the layer-by-layer construction process in the fabrication of the new Ni-Co based superalloy in EBSL. The EBSL-Ni-Co superalloy, when subjected to the alternating reduction cooling method, exhibited an internal stress of 49 MPa. This value represents a significant reduction of 83.8% compared to the internal stress observed when employing the linear reduction cooling method. Additionally, the solvus temperature of the gamma - gamma ' eutectic phases in EBSL-Ni-Co superalloys produced by the alternating reduction cooling method is significantly higher. Intriguingly, the N th layer of the EBSL-Ni-Co based superalloys produced by EBSL simultaneously heats treated with the preceding layers. And the low melting point phase gradually dissolved back into the matrix. The implementation of an alternating reduced cooling method successfully mitigated the formation of the liquid film in the gamma - gamma ' eutectic phase and the buildup of internal stresses in the EBSL-Ni-Co superalloy during its manufacturing process. These discoveries open up a novel preparation procedure pathway for the manufacture of crack-free superalloys with superior mechanical characteristics using EBSL. (c) 2023 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

Microstructural evolution of a Y2O3 network reinforced Ni–Co based superalloy fabricated by spark plasma sintering

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Spark Plasma Sintering Cobalt Base Superalloy Strengthened by Y–Cr–O Compound Through High-Energy Milling

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Microstructure, Phase Transformation and Mechanical Property of Ni-Co-Mn-In Alloy Prepared by Spark Plasma Sintering

Effect of yttrium addition on microstructural evolution and high temperature mechanical properties of Ni-based superalloy produced by selective laser melting

Microstructure and mechanical properties of Y2O3 reinforced Ti6Al4V composites fabricated by spark plasma sintering

Microstructural Evolution and Mechanical Properties of a High Yttrium Containing TiAl Based Alloy Densified by Spark Plasma Sintering

Microstructure development of Y–Ti–O dispersion strengthened Cu alloys fabricated by mechanical alloying

Effect of Y2O3 Addition on the Microstructure, Wear Resistance, and Corrosion Behavior of W-4.9Ni-2.1Fe Heavy Alloy

Microstructure evolution of a nickel‐based powder metallurgy superalloy under different solution treatment temperatures

Crack Inhibition and Performance Modification of NiCoCr-Based Superalloy with Y2O3 Nanoparticles by Laser Metal Deposition

Effect of Melt Superheat Treatment on Solidification Behavior and Microstructure of New Ni–Co Based Superalloy

Microstructure and Mechanical Properties of Spark Plasma Sintered CoCrFeNiNbX High-Entropy Alloys with Si Addition

Microstructure Evolution and Mechanical Performance of Nickel Based Superalloy C1023 at Elevated Temperatures

Microstructure and Mechanical Properties of Nickel Strengthened by Y2O3 Through Rock-Milling and Spark Plasma Sintering

Improvement In Microstructure Homogeneity Of Sintered Compacts Through Powder Treatments And Alloy Designs

Microalloying effects of Y on performance of cast nickel-based superalloy IN713C

Microstructure Control and Hot Cracking Behavior of the New Ni-Co Based Superalloy Prepared by Electron Beam Smelting Layered Solidification Technology

Phase, Microstructure and Properties Evolution of Fine-Grained W–Mo–Ni–Fe Alloy During Spark Plasma Sintering