Abstract:Uniform distribution of Cr2AlC MAX phase plays a crucial role in evolution of microstructure and mechanical properties. The incorporation of Cr2AlC MAX phase with and without milling in conventionally sintered WHA significantly enhances refinement of W‐grains. Combination of grain size refinement and dispersion strengthening results in the improvement of tensile properties This study focuses on the role of Cr2AlC‐MAX phase incorporation on the density, phase composition, microstructure, and mechanical properties of 90W‐6Ni‐2Fe‐2Co heavy alloy. The blended powders are ball milled in a high‐energy ball mill up to 40 h, compacted, and sintered at 1500 °C. The mechanical alloying results in a refined microstructure with uniform distribution of W, matrix, and dispersoids. The minimum grain size of W (14.7 ± 5.6 μm) is obtained in 2 wt% Cr2AlC‐containing tungsten alloy prepared from 40 h‐milled powders. Among the investigated alloys, 1 wt% Cr2AlC‐incorporated samples exhibit maximum compressive stress (2026 MPa). The incorporation of fine Cr2AlC as dispersoids is found to be beneficial in improving the strength as well as ductility of WHAs. The best combination of yield strength (553.4 MPa), ultimate tensile strength (1011.2 MPa), ductility (11.4%), and product of strength and elongation (11.5 GPa%) is found in alloy prepared from 40 h milled 90W‐4.8Ni‐1.6Fe‐1.6Co‐2Cr2AlC. The improved tensile strength in Cr2AlC‐incorporated WHAs may be attributed to the combined effect of grain size refinement and dispersion strengthening. Overall, the combination of ball milling and Cr2AlC incorporation in tungsten‐heavy alloys is found to be effective in developing a novel W‐based alloy system for strategic applications.

Spark Plasma Sintering Cobalt Base Superalloy Strengthened by Y–Cr–O Compound Through High-Energy Milling

Microstructural evolution of a Y2O3 network reinforced Ni–Co based superalloy fabricated by spark plasma sintering

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

Synthesis and Properties of an Ultrafine Grained Ti-45al-2cr-2nb-1b-0.5ta Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

Hardness and Corrosion Behavior of CrMnFeCoNi Alloy Fabricated by Ball Milling and Spark Plasma Sintering

Microstructure and Mechanical Properties of Tial-Based Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

The Microstructure and Properties of Fine Crystalline Al-50Si Alloy Prepared by High-Energy Ball Milling

Microstructure and thermal stability of MoSi2-CoNiCrAlY nanocomposite feedstock prepared by high energy ball milling

Effect of High‐Energy Ball‐Milling Duration on Densification, Microstructure, and Mechanical Properties of Cr2AlC‐Dispersed 90W‐6Ni‐2Fe‐2Co Heavy Alloys

The Influence of Ball Milling Time and Sintering Temperature on the Structural and Capabilities of FeCoCrNiMn High-Entropy Alloy

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Characterization of MCrAlY/nano-Al2O3 nanocomposite powder produced by high-energy mechanical milling as feedstock for high-velocity oxygen fuel spraying deposition

Microstructure, Phase Transformation and Mechanical Property of Ni-Co-Mn-In Alloy Prepared by Spark Plasma Sintering

Effects of milling time and sintering temperature on the mechanical properties of 8 wt% WC/AlCoCrFeNiTi 0.5 high entropy alloy matrix composite

Enhancement of γ/γ' Microstructured Cobalt Superalloys Produced from Atomized Powder by Creating a Harmonic Structure

The Microstructures and Mechanical Properties of a 5vol%sic/aa2024 Nanocomposite Fabricated by Powder Metallurgy

Microstructural Evolution and Densification of Co-Based Alloy Powder by Spark Plasma Sintering for High-Hardness Applications

Preparation of Ti-45Al-5.5(Cr,Nb,B,Ta) Alloy by Mechanical Milling and Spark Plasma Sintering

The Influence of High-Energy Ball Milling and Sintering Process on the Microstructure and Mechanical Properties of Al-Ni-Y-Co-La Alloy

Microstructure and mechanical properties of Y2O3 reinforced Ti6Al4V composites fabricated by spark plasma sintering