Abstract:Fine-grained metals have attracted much interest due to the possibility to obtain both high strength and high ductility.Studies of the deformation mechanisms in fine-grained metals are therefore important,and can also help fill a gap in knowledge between nano-grained metals and conventional coarse-grained metals,which is an area of both scientific and industrial interest.For such an investigation it is very important to use a starting material with a simple microstructure.For this purpose spark plasma sintering(SPS) has been used to prepare samples of fully dense,fine-grained Al with average grain sizes ranging from 0.8μm to 5.2μm,in a fully recrystallized condition,with equiaxed grains and a random texture.The microstructures and mechanical properties of these sintered finegrained Al samples have been studied using EBSD,TEM and compression testing.Based on these studies,relationships between the microstructure and mechanical properties have been established. The results show that the formation of deformation microstructure depends on grain size.During deformation,all grains in samples with an average grain size of 5.2μm show grain subdivision by dislocation boundary formation,though few grains in a sample with an average grain size of 0.8μm show dislocation boundary formation.The mechanical properties of fine-grained Al show a transition in behavior with decreasing average grain size.For samples with an average grain size of 1.3μm,stressstrain curves show yield drop phenomenon,attributed to source-limited hardening.For a sample with an average grain size of 0.8μm,the stress-strain curve shows only limited work-hardening after yielding,in agreement with the observation of the limited formation of dislocation boundaries inside grains during deformation.For a sample with average grain size of 5.2μm the average dislocation boundary misorientation angle increases more quickly than in deformed conventional coarse-grained Al deformed to the same strain,due to the effect of increased volume fraction of grain boundaries and oxide particles.The strength of the SPS-prepared Al samples is higher than found for samples with identical grain sizes prepared by thermo-mechanical deformation,due to the presence of oxide particles,and to source-limited hardening for samples with average grain sizes smaller than 1.3μm.

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Microstructure, Densification and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated by Spark Plasma Sintering

Microstructure and strengthening mechanisms of novel lightweight TiAlV0.5CrMo refractory high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

Effect of Mechanical Alloying on the Microstructure and Properties of W–Ti Alloys Fabricated by Spark Plasma Sintering

Mechanical Properties of Cu70Fe30 (at%) Bulk Metastable Alloys Prepared by Mechanical Alloying and Spark Plasma Sintering

Fabrication of a novel multiscale structured 5083 Al alloy with improved tensile properties via mechanical milling and spark plasma sintering

Preparation of TiAl15Si15 intermetallic alloy by mechanical alloying and the spark plasma sintering method

The effects of powder size and sintering temperature on the microstructure and properties of modified MA6000 alloy produced by spark plasma sintering

Effects of Sintering Temperature and Holding Time on Microstructure and Mechanical Properties of Ti−1Al−8V−5Fe Prepared by Spark Plasma Sintering

Effect of Processing Routes on Microstructural Development, Mechanical Properties, and Wear Behavior of Ti6Al4V Alloy

Microstructures Of Components Synthesized Via Electron Beam Selective Melting Using Blended Pre-Alloyed Powders Of Ti6al4v And Ti45al7nb

Microstructures and Mechanical Properties of Sintered Fine-Grained Al

Microstructure and Mechanical Properties of Ti-6Al-4V Manufactured by Selective Laser Melting after Stress Relieving, Hot Isostatic Pressing Treatment, and Post-Heat Treatment

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Tensile Behavior of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting: Effects of Microstructures and As-Built Surface Quality

In-situ synthesized a dual-scale Ti 2 AlC reinforced TiAl composites with superior mechanical properties

Spark Plasma Sintering of Pure Titanium: Microstructure and Mechanical Characteristics

Microstructures and mechanical properties during sinter-forging of a novel TiAl alloy

Effect of tungsten micro-scale dispersed particles on the microstructure and mechanical properties of Ti–6Al–4V alloy

Microstructure, Phase Transformation and Mechanical Property of Ni-Co-Mn-In Alloy Prepared by Spark Plasma Sintering