Abstract:Fine-grained metals have attracted much interest due to the possibility to obtain both high strength and high ductility.Studies of the deformation mechanisms in fine-grained metals are therefore important,and can also help fill a gap in knowledge between nano-grained metals and conventional coarse-grained metals,which is an area of both scientific and industrial interest.For such an investigation it is very important to use a starting material with a simple microstructure.For this purpose spark plasma sintering(SPS) has been used to prepare samples of fully dense,fine-grained Al with average grain sizes ranging from 0.8μm to 5.2μm,in a fully recrystallized condition,with equiaxed grains and a random texture.The microstructures and mechanical properties of these sintered finegrained Al samples have been studied using EBSD,TEM and compression testing.Based on these studies,relationships between the microstructure and mechanical properties have been established. The results show that the formation of deformation microstructure depends on grain size.During deformation,all grains in samples with an average grain size of 5.2μm show grain subdivision by dislocation boundary formation,though few grains in a sample with an average grain size of 0.8μm show dislocation boundary formation.The mechanical properties of fine-grained Al show a transition in behavior with decreasing average grain size.For samples with an average grain size of 1.3μm,stressstrain curves show yield drop phenomenon,attributed to source-limited hardening.For a sample with an average grain size of 0.8μm,the stress-strain curve shows only limited work-hardening after yielding,in agreement with the observation of the limited formation of dislocation boundaries inside grains during deformation.For a sample with average grain size of 5.2μm the average dislocation boundary misorientation angle increases more quickly than in deformed conventional coarse-grained Al deformed to the same strain,due to the effect of increased volume fraction of grain boundaries and oxide particles.The strength of the SPS-prepared Al samples is higher than found for samples with identical grain sizes prepared by thermo-mechanical deformation,due to the presence of oxide particles,and to source-limited hardening for samples with average grain sizes smaller than 1.3μm.

Microstructures and Mechanical Properties of Sintered Fine-Grained Al

Structure and Strength of Aluminum with Sub-Micrometer/micrometer Grain Size Prepared by Spark Plasma Sintering

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Influence of Grain Size in the Near-Micrometre Regime on the Deformation Microstructure in Aluminium

Microstructures and mechanical properties of Si and Zr modified Al–Zn–Mg–Cu alloy-A comparison between selective laser melting and spark plasma sintering

Structure and mechanical behavior of ultrafine-grained aluminum-iron alloy stabilized by nanoscaled intermetallic particles

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Graded Microstructure and Mechanical Properties of Spark Plasma Sintered Fe-Cr alloys

In situ studies on temperature‐dependent deformation mechanisms of Al2O3 prepared by spark plasma sintering

Microstructure and Mechanical Strength of Near- and Sub-Micrometre Grain Size Copper Prepared by Spark Plasma Sintering

Effects of sintering time on the microstructure and properties of an Al-Cu-Mg alloy

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Quantification of Deformation Microstructure at Ultra-Low Tensile Strain in Pure Al Prepared by Spark Plasma Sintering

Research Progress on the Microstructure Evolution Mechanisms of Al-Mg Alloys by Severe Plastic Deformation

Microstructure, Densification and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated by Spark Plasma Sintering

Plastic Yielding and Tensile Strength of Near-Micrometer Grain Size Pure Iron

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Mechanical Properties of Cu70Fe30 (at%) Bulk Metastable Alloys Prepared by Mechanical Alloying and Spark Plasma Sintering

Microstructure and Mechanical Properties of Sintered and Forged Fe-2Cu-0.5C-0.11S Materials

Microstructure, Phase Transformation and Mechanical Property of Ni-Co-Mn-In Alloy Prepared by Spark Plasma Sintering

Achieving Strength-Ductility Synergy of Spark Plasma Sintered (cocrni)94al3ti3 Medium-Entropy Alloy Via Post-Sintering In-Situ Precipitation Treatment