Abstract:Fine-grained metals have attracted much interest due to the possibility to obtain both high strength and high ductility.Studies of the deformation mechanisms in fine-grained metals are therefore important,and can also help fill a gap in knowledge between nano-grained metals and conventional coarse-grained metals,which is an area of both scientific and industrial interest.For such an investigation it is very important to use a starting material with a simple microstructure.For this purpose spark plasma sintering(SPS) has been used to prepare samples of fully dense,fine-grained Al with average grain sizes ranging from 0.8μm to 5.2μm,in a fully recrystallized condition,with equiaxed grains and a random texture.The microstructures and mechanical properties of these sintered finegrained Al samples have been studied using EBSD,TEM and compression testing.Based on these studies,relationships between the microstructure and mechanical properties have been established. The results show that the formation of deformation microstructure depends on grain size.During deformation,all grains in samples with an average grain size of 5.2μm show grain subdivision by dislocation boundary formation,though few grains in a sample with an average grain size of 0.8μm show dislocation boundary formation.The mechanical properties of fine-grained Al show a transition in behavior with decreasing average grain size.For samples with an average grain size of 1.3μm,stressstrain curves show yield drop phenomenon,attributed to source-limited hardening.For a sample with an average grain size of 0.8μm,the stress-strain curve shows only limited work-hardening after yielding,in agreement with the observation of the limited formation of dislocation boundaries inside grains during deformation.For a sample with average grain size of 5.2μm the average dislocation boundary misorientation angle increases more quickly than in deformed conventional coarse-grained Al deformed to the same strain,due to the effect of increased volume fraction of grain boundaries and oxide particles.The strength of the SPS-prepared Al samples is higher than found for samples with identical grain sizes prepared by thermo-mechanical deformation,due to the presence of oxide particles,and to source-limited hardening for samples with average grain sizes smaller than 1.3μm.

Quantification of Deformation Microstructure at Ultra-Low Tensile Strain in Pure Al Prepared by Spark Plasma Sintering

In-situ Study of Microstructural Evolution and Local Strain Distribution During Tensile Loading of Near-Micrometre Grain Size Aluminium

Strain Distribution and Lattice Rotations During In-Situ Tension of Aluminum with a Transmodal Grain Structure

Influence of Grain Size in the Near-Micrometre Regime on the Deformation Microstructure in Aluminium

In-situ synchrotron X-ray micro-diffraction investigation of ultra-low-strain deformation microstructure in laminated Ti-Al composites

Investigation of Plastic Yielding in Near-Micrometer Grain Size Aluminum Using Synchrotron Microdiffraction

In situ studies on temperature‐dependent deformation mechanisms of Al2O3 prepared by spark plasma sintering

Microstructures and Mechanical Properties of Sintered Fine-Grained Al

Investigation of Deformation Microstructures in Spark Plasma Sintered Nickel

Microstructure and flow stress of polycrystals and single crystals

Local Deformation Mechanisms in Metal Systems with a Tailored Grain Size Distribution

Achieving a Compatible Tensile Strength and Ductility of Bulk Ultrafine Grained Al by Spark Plasma Sintering Plus Annealing

In Situ Synchrotron X-ray Micro-Diffraction Investigation of Elastic Strains in Laminated Ti-Al Composites

Understanding the Strain Path Effect on the Deformed Microstructure of Single Crystal Pure Aluminum

Effects of Annealing and Extrusion on the Microstructure and Tensile Properties of Ultrafine-Grained Al Fabricated by Spark Plasma Sintering

In-situ EBSD Study of the Active Slip Systems and Lattice Rotation Behavior of Surface Grains in Aluminum Alloy During Tensile Deformation

Investigation of Grain Subdivision at Very Low Plastic Strains in A Magnesium Alloy

3D Microstructural and Strain Evolution During the Early Stages of Tensile Deformation

3Dxrd Measurements of Lattice Rotations in Tensile Deformed if Steel

Investigation of the Deformation Structure in an Aluminium Magnesium Alloy by High Angular Resolution Three-Dimensional X-Ray Diffraction

A complete grain-level assessment of the stress-strain evolution and associated deformation response in polycrystalline alloys