Abstract:The micro-mechanical behavior of lamellar structured Ti6Al4V alloy was studied upon a small strain of 4.5 % compressional loading. The strain and stress concentration is found highly related to individual crystallographic orientation, their size, shape and grain-grain interaction, which usually concentrated along grain boundaries (GBs) typically soft and hard GBs owing to the strong strain gradient incurred. The generated local plastic deformation forms ledges through dislocation accumulation which further activate large amount of Geometrically necessary dislocations (GNDs) to accomodate strain incompatibility. Both strain and stress is maximized at some triple points (TPs). EBSD and crystal plasticity (CP) simulation disclosed some long range meso-bands (about 45° to loading direction) across multi-grains and mini-bands within grain interiors (GIs) with concentrated strain behavior which demonstrate slip and ductile behavior of the Ti6Al4V material. Prismatic slip is found dominated the slip behavior of the Ti6AL4V alloy (mostly from surface dislocation activation) which is away from some findings of literature and largely determined by its low critical resolved shear stress (CRSS). Dislocation is observed emitted from high angle grain boundaries (HAGBs) while slip transmission is observed through both low (LAGBs) and HAGBs. The substructures (α-lamellae), a type of LAGBs allocated within α-colonies, have no significant effect to dislocation movement. Fatigue failure can be inferred from the early stage of micro-mechanical behavior mainly judged by the amount of accumulated plastic deformation and induced stress/strain distribution amont the surroundings. Crack may nucleate from easy prismatic slip, local strain accumulation induced by soft and hard grain clustering (either hard embedded in soft or vice versa usually start from some TPs and sharp corners), or some concentrated long range slip activities. Other than the surface dents induced failure, shearing, cleavage, multi-cleavage and intergranular patterns is presumed highly related to the local microstructure, including their relative size, shape, orientation and grain-grain interactions. The multiple crack origins deemed for reduce fatigue life of shot peened samples regardless of the surface compressional residual stress being generated. The work helps understand the micro-mechanical deformation behavior (down to dislocation level) of Ti6Al4V alloy. Their fatigue and fracture can be inferred from such early stage of strain/stress behavior considering microstructural heterogeneities for similar alloys.

In-situ synchrotron X-ray micro-diffraction investigation of ultra-low-strain deformation microstructure in laminated Ti-Al composites

Revealing interface-assisted plastic anisotropy <i>via in situ</i> transmission electron microscopy tension of lamellar TiAl

Extraordinary room temperature tensile ductility of laminated Ti/Al composite: Roles of anisotropy and strain rate sensitivity

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

In-situ investigation of deformation behavior and fracture forms of Ti/Al/Mg/Al/Ti laminates

In-situ investigation on tensile properties of a novel Ti/Al composite sheet

Unraveling hot deformation behavior and microstructure evolution of nanolamellar TiAl/Ti3Al composites

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

In Situ Electron Backscatter Diffraction Study of Deformation Inhomogeneity under Uniaxial Tension of Laser Melting Deposited TA15 Alloy

Balancing the strength and ductility of Ti2AlC/TiAl composite with a bioinspired micro-nano laminated architecture

In-situ study of tensile behavior of Ti/Al laminated metal composites fabricated via ultrasonic additive manufacturing

Micro-mechanical behavior of lamellar structured Ti6Al4V alloy upon compression via experimental and crystal plasticity study

High temperature micro-deformation behavior of continuous TiNb fiber reinforced TiAl matrix composite investigated by in-situ high-energy X-ray diffraction

In Situ Synchrotron X-ray Diffraction Analysis of Deformation Behaviour in Ti-Ni-based Thin Films.

In-situ synchrotron X-ray diffraction investigation on deformation behavior of Nb/NiTi composite during pre-straining process

In-Situ Observation of Fracture Behavior of Ti-Aluminide Multi-Layered Composites Produced by a Hybrid Sintering Process

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

Micro-/nano-scale structure and elemental diffusion in the Al/Ti/Al sandwich structure

Activating dispersed strain bands in tensioned nanostructure layer for high ductility: The effects of microstructure inhomogeneity