Abstract:The deformation-induced surface roughening of an Al-Mg alloy is analyzed using a combination of experiments and modeling. A mesoscale oligocrystal of AA5052-O, obtained by recrystallization annealing and subsequent thickness reduction by machining, that contains approx. 40 grains is subjected to uniaxial tension. The specimen contains one layer of grains through the thickness. A laser confocal microscope is used to measure the surface topography of the deformed specimen. A finite element model with realistic (non-columnar) shapes of the grains based on a pair of Electron Back-Scatter Diffraction (EBSD) scans of a given specimen is constructed using a custom-developed shape interpolation procedure. A Crystal Plasticity Finite Element (CPFE) framework is then applied to the voxel model of the tension test of the oligocrystal. The unknown material parameters are determined inversely using an efficient, custom-built optimizer. Predictions of the deformed shape of the specimen, surface topography, evolution of the average roughness with straining and texture evolution are compared to experiments. The model reproduces the averaged features of the problem, while missing some local details. As an additional verification of the CPFE model, the statistics of surface roughening are analyzed by simulating uniaxial tension of an AA5052-O polycrystal and comparing it to experiments. The averaged predictions are found to be in good agreement with the experimentally observed trends. Finally, using the same polycrystalline specimen, texture–morphology relations are discovered, using a symbolic Monte Carlo approach. Simple relations between the Schmid factor and roughness can be inferred purely from the experiments. Novelties of this work include: realistic 3D shapes of the grains; efficient and accurate identification of material parameters instead of manual tuning; a fully analytical Jacobian for the crystal plasticity model with quadratic convergence; novel texture–morphology relations for polycrystal.

A complete grain-level assessment of the stress-strain evolution and associated deformation response in polycrystalline alloys

Grain-level Statistical Plasticity Analysis on Strain Cycle Fatigue of a FCC Metal

Anisotropy of Yielding/Hardening and Micro-Inhomogeneity of Deforming/Rotating for A Polycrystalline Metal under Cyclic Tension Compression

Micro-failure of metals under inhomogeneous plastic deformation

Grain polydispersity and coherent crystal reorientations are features to foster stress hotspots in polycrystalline alloys under load

Microstructure and flow stress of polycrystals and single crystals

4223 - ANALYSIS ON CYCLIC PLASTICITY AND STRESS DISTRIBUTION OF POLYCRYSTAL AT GRAIN LEVEL

In situ measurement of three-dimensional intergranular stress localizations and grain yielding under elastoplastic axial-torsional loading

Experimental Investigation of Polycrystalline Material Deformation Based on a Grain Scale

Automated Analysis Framework of Strain Partitioning and Deformation Mechanisms Via Multimodal Fusion and Computer Vision

Microstrain and grain-size analysis from diffraction peak width and graphical derivation of high-pressure thermomechanics

Recoverable Creep Deformation and Transient Local Stress Concentration Due to Heterogeneous Grain-Boundary Diffusion and Sliding in Polycrystalline Solids

In-situ EBSD Study of the Active Slip Systems and Lattice Rotation Behavior of Surface Grains in Aluminum Alloy During Tensile Deformation

Simulation of Deformation and Fracture in Polycrystalline Aluminum Alloy under Dynamic Loading

Deformation-Induced Surface Roughening of an Aluminum–Magnesium Alloy: Experimental Characterization and Crystal Plasticity Modeling

Description of Dynamic Recrystallization by Means of an Advanced Statistical Multilevel Model: Grain Structure Evolution Analysis

Evaluating the grain-scale deformation behavior of a single-phase FCC high entropy alloy using synchrotron high energy diffraction microscopy

Study of Microstructural Grain and Geometric Size Effects on Plastic Heterogeneities at Grain-Level by Using Crystal Plasticity Modeling with High-Fidelity Representative Microstructures

Influences of granular constraints and surface effects on the heterogeneity of elastic, superelastic, and plastic responses of polycrystalline shape memory alloys

Quantification of Slip Band Distribution in Polycrystals: An Automated Fast Fourier Transform Decomposition Approach

Comprehensive Study of Plastic Deformation Mechanism of Polycrystalline Copper Using Crystal Plasticity Finite Element