Abstract:This study aims at introducing the back stress of anisotropic strain-hardening into the crystal plasticity theory and demonstrating the rationality of this crystal plasticity model to describe the evolution of the subsequent yield surface of polycrystalline aluminum at the mesoscopic scale under complex pre-cyclic loading paths. By using two different scale finite element models, namely a global finite element model (GFEM) as the same size of the thin-walled tube specimen used in the experiments and a 3D cubic polycrystalline aggregate representative volume element (RVE) model, the evolution of the subsequent yield surface for different unloading cases after 30 pre-cycles is further performed by experiments and numerical simulations within a crystal plasticity finite element (CPFE) frame. Results show that the size and shape of the subsequent yield surfaces are extremely sensitive to the chosen offset strain and the pre-cyclic loading direction, which present pronounced anisotropic hardening through a translation and a distortion of the yield surface characterized by the obvious "sharp corner" in the pre-deformation direction and "flat" in the reverse direction by the definition of small offset strain, while the subsequent yield surface exhibits isotropic hardening reflected by the von Mises circle to be distorted into an ellipse by the definition of large offset strain. In addition, the heterogeneous properties of equivalent plastic strain increment are further discussed under different offset strain conditions. Modeling results from this study show that the heterogeneity of plastic deformation decreases as a law of fraction exponential function with the increasing offset strain. The above analysis indicates that anisotropic hardening of the yield surface is correlated with heterogeneous deformation caused by crystal microstructure and crystal slip. The crystal plasticity model based on the above microscopic mechanism can accurately capture the directional hardening features of the yield surface.

Simulation of Deformation and Fracture in Polycrystalline Aluminum Alloy under Dynamic Loading

Experimental and numerical investigation on plasticity and fracture behaviors of aluminum alloy 6061-T6 extrusions

Dynamic plasticity of AZ31 magnesium alloy: Experimental investigation and constitutive modeling

Study of dynamic mechanical behavior of 1060-H112 aluminum alloy: Experimental and numerical simulation

Experimental and Physical-Based Constitutive Model Study of Fcc Metal over Wide Temperature and Strain Rate Ranges

Deformation-Induced Surface Roughening of an Aluminum–Magnesium Alloy: Experimental Characterization and Crystal Plasticity Modeling

Microstructure evolution, constitutive modeling and forming simulation of AA6063 aluminum alloy in hot deformation

Phase-Field Modeling of Coupled Brittle-Ductile Fracture in Aluminum Alloys

Dynamic Mechanical Properties and Modification of Fracture Criteria of 6061-T651 Aluminum Alloy

A Physically Based Constitutive Model and Continuous Dynamic Recrystallization Behavior Analysis of 2219 Aluminum Alloy during Hot Deformation Process

Modelling Dynamic Recrystallization of A356 Aluminum Alloy during Hot Deformation

Microstructure Evolution and Dynamic Recrystallized Model of 5083 Aluminum Alloy During Hot Deformation

A complete grain-level assessment of the stress-strain evolution and associated deformation response in polycrystalline alloys

Numerical Analysis of Experiments on Damage and Fracture Behavior of Differently Preloaded Aluminum Alloy Specimens

The Influence of the Volume Fraction of Ceramic Particles on the Plastic Strain Localization and Fracture of Metal Matrix Composites. Computational Analysis

Strain rate effect of high purity aluminum single crystals: Experiments and simulations

Plasticity and ductile fracture modeling of an Al–Si–Mg die-cast alloy

Dynamic Behavior of Aluminum Alloy Aw 5005 Undergoing Interfacial Friction and Specimen Configuration in Split Hopkinson Pressure Bar System at High Strain Rates and Temperatures

Characterization and constitutive analysis-based crystal plasticity of warm flow and fracture behaviours of 2060 Al-Cu-Li alloy

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

Characterization and prediction of fracture in 6000- and 7000-series aluminum alloy sheet under various stress states