Abstract:Powder metallurgy (PM) technology is expected to provide a promising strategy for the cost-effective and highly efficient utilization of spherical Ti–6Al–4V powders with particles size of large than 150 μm to reduce material waste. However, how to overcome the problem of low sinterability and poor ductility of coarse lamellar microstructures of large-diameter spherical powders are still remains a significant challenge. In this study, Ti–6Al–4V alloys were prepared by spark plasma sintering (SPS) at different sintering temperatures with plasma rotating electrode process (PREP) large-diameter spherical powders (∼156 μm). The microstructure evolution, grain structure, mechanical properties and fracture mechanisms were systematically investigated. Results demonstrate that the acicular martensite structure inside the unmelted particles changed to a uniform and fine α/β lamellar microstructure with the increased sintering temperature. Consequently, the Ti–6Al–4V alloys exhibit excellent strength-ductility at 925 °C. (ultimate tensile strength of 881 MPa and elongation up to 14.8 %). Fundamentally, the excellent strength-ductility was attributed to the uniform and dense fine α/β lamellar structure that enhanced the effective bearing area during deformation. The stacked dislocations at the α/β phase interface provided high strength. In addition, the high-density α/β phase interface in the matrix reduced the mean free path of the dislocation, which resulted in a high strain hardening rate of the high-density geometrically necessary dislocations (GNDs) and delayed the premature fracture. The intergranular brittle fracture mode of the alloys changed to the ductile fracture mode. These findings have important implications for recycling super-large diameter spherical powders.

Microstructure, Densification and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated by Spark Plasma Sintering

The process and mechanical properties of Nb–Si–Mo–Ti alloy prepared by spark plasma sintering

Microstructure, Phase Transformation and Mechanical Property of Ni-Co-Mn-In Alloy Prepared by Spark Plasma Sintering

Microstructure, densification and mechanical properties of in situ TiBw/Ti2AlNb composites fabricated by spark plasma sintering

Microstructure Evolution, B2 Grain Size Uniformity, and Performance of a Powder Metallurgy Ti-22Al-25Nb Alloy during Solution Treatment

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Effects of Sintering Temperature and Holding Time on Microstructure and Mechanical Properties of Ti−1Al−8V−5Fe Prepared by Spark Plasma Sintering

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Achieving excellent strength-ductility combination in Ti–6Al–4V alloy by spark plasma sintering technology using large-diameter PREP spherical powder

Microstructure and Mechanical Properties of the Powder Metallurgy Nb-16Si-24Ti-2Al-2Cr Alloy

Cu-Al-Ni Nanocrystalline Compacts Obtained by Spark Plasma Sintering of Mechanically Alloyed Powders

Microstructural characterization and mechanical behaviors of Ti-xNb alloys (x = 34–44.at%) fabricated by spark plasma sintering: The role of sintering temperature and Nb content

Sintering Behavior and Mechanical Properties of Ti–TiBw Composites Prepared with Pre‐alloyed Ti–TiBw Composite Powders

Spark Plasma Sintering of W-10Ti Alloys: Microstructure, Properties and Grain Growth Kinetics

Effect of spark plasma sintering temperature on the multi-scale microstructure evolution and mechanical properties of Ti 2 AlC/TiAl composites with network architecture

Microstructure and mechanical properties of Ti6Al4V alloy prepared by oscillatory pressure sintering

Preparation of TiAl15Si15 intermetallic alloy by mechanical alloying and the spark plasma sintering method

Microstructural Characterization and Prior Particle Boundary (PPB) of PM Nickel-Based Superalloys by Spark Plasma Sintering (SPS)

Microstructural Evolution and Mechanical Properties of Spark Plasma Sintering of Tantalum-Tungsten Alloy

Spark Plasma Sintering of Pure Titanium: Microstructure and Mechanical Characteristics

Spark Plasma Sintering of Titanium Aluminides: A Progress Review on Processing, Structure-Property Relations, Alloy Development and Challenges