Abstract:Powder metallurgy (PM) technology is expected to provide a promising strategy for the cost-effective and highly efficient utilization of spherical Ti–6Al–4V powders with particles size of large than 150 μm to reduce material waste. However, how to overcome the problem of low sinterability and poor ductility of coarse lamellar microstructures of large-diameter spherical powders are still remains a significant challenge. In this study, Ti–6Al–4V alloys were prepared by spark plasma sintering (SPS) at different sintering temperatures with plasma rotating electrode process (PREP) large-diameter spherical powders (∼156 μm). The microstructure evolution, grain structure, mechanical properties and fracture mechanisms were systematically investigated. Results demonstrate that the acicular martensite structure inside the unmelted particles changed to a uniform and fine α/β lamellar microstructure with the increased sintering temperature. Consequently, the Ti–6Al–4V alloys exhibit excellent strength-ductility at 925 °C. (ultimate tensile strength of 881 MPa and elongation up to 14.8 %). Fundamentally, the excellent strength-ductility was attributed to the uniform and dense fine α/β lamellar structure that enhanced the effective bearing area during deformation. The stacked dislocations at the α/β phase interface provided high strength. In addition, the high-density α/β phase interface in the matrix reduced the mean free path of the dislocation, which resulted in a high strain hardening rate of the high-density geometrically necessary dislocations (GNDs) and delayed the premature fracture. The intergranular brittle fracture mode of the alloys changed to the ductile fracture mode. These findings have important implications for recycling super-large diameter spherical powders.

Microstructure and mechanical properties of Ti6Al4V alloy prepared by oscillatory pressure sintering

Microstructure and Mechanical Properties of ZTA Composites Fabricated by Oscillatory Pressure Sintering

Microstructure, Densification and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated by Spark Plasma Sintering

Improved Mechanical Properties of Al2O3-25 Vol% SiCw Composites Prepared by Oscillatory Pressure Sintering

Microstructure regulation of titanium-oxygen alloy with high strength and excellent ductility for biomedical applications

Preparation, Characterization and Designing of Porous Ti–6Al–4V Through Metal Injection Molding Without Space Holder

Enhanced Properties of Pure Alumina Ceramics by Oscillatory Pressure Sintering

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Mechanical behavior and microstructure control of the low-cost titanium-oxygen alloy prepared by ball milling and spark plasma sintering

A Novel Approach to Improve Flexural Strength of Al2O3‐20 Wt% ZrO2 Composites by Oscillatory Pressure Sintering

Microstructure and Mechanical Properties of Zirconia Ceramics Consolidated by a Novel Oscillatory Pressure Sintering

Achieving excellent strength-ductility combination in Ti–6Al–4V alloy by spark plasma sintering technology using large-diameter PREP spherical powder

Enhanced Toughness and Reliability of Si3N4-SiCw Composites under Oscillatory Pressure Sintering

A study of the microstructures and mechanical properties of Ti6Al4V fabricated by SLM under vacuum

Simultaneously enhancing strength and ductility of Ti-6Al-4V alloy with the hierarchical structure via a novel thermal annealing treatment

Effects of Sintering Temperature and Holding Time on Microstructure and Mechanical Properties of Ti−1Al−8V−5Fe Prepared by Spark Plasma Sintering

Fabrication and Mechanical Properties of ZrO2–Al2O3–SiC(w) Composites by Oscillatory Pressure Sintering

Microstructures and mechanical properties during sinter-forging of a novel TiAl alloy

An Oscillatory Pressure Sintering of Zirconia Powder: Densification Trajectories and Mechanical Properties

A transmission electron microscopy and three-dimensional atom probe study of the oxygen-induced fine microstructural features in as-sintered Ti–6Al–4V and their impacts on ductility

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics