Abstract:Heterostructured materials address the inherent trade-off between strength and toughness, allowing alloys to enhance toughness while simultaneously increasing strength. However, the regulation of heterostructures and the preparation of large-volume specimens remain significant challenges. The aim of this study was to prepare gradient-structured 5083 aluminum alloys using the constrained deformation method and to investigate its effects on the comprehensive mechanical properties. Additionally, the strengthening mechanisms of the constrained deformation specimens were elucidated. The microstructure was characterized using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The mechanical properties were assessed through microhardness and uniaxial tensile tests. The findings indicate that the constrained deformation treated 5083 aluminum alloy exhibits a substantial improvement in comprehensive mechanical performance. In comparison to the as-received specimens, the yield strength of the constrained deformation specimens (CDS) significantly increases with the increases volume fraction of the DL. Nonetheless, these specimens maintain an average elongation at break ranging from 12.3% to 14.3%. The enhanced properties of the gradient-structured 5083 aluminum alloy are primarily attributed to the high density of geometrically necessary dislocations (GNDs) and the elevated proportion of low-angle grain boundaries (LAGBs). Specifically, the increase in dislocation density contributes significantly to the alloy's strength, while additional heterogeneous deformation-induced (HDI) hardening, along with a high proportion of LAGBs, preserves the alloy's excellent toughness. This study provides novel insights and methodologies for the optimal design and large-scale application of heterostructures in aluminum alloys.

Fabrication of a novel multiscale structured 5083 Al alloy with improved tensile properties via mechanical milling and spark plasma sintering

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Bulk nanocrystalline aluminum 5083 alloy fabricated by a novel technique: Cryomilling and spark plasma sintering

Effect of Mechanical Alloying on Microstructure and Mechanical Properties of Ti-24Nb-4Zr-3Mn Alloys Prepared by Spark Plasma Sintering

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Microstructure and Mechanical Properties of Tial-Based Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

Achieving a Compatible Tensile Strength and Ductility of Bulk Ultrafine Grained Al by Spark Plasma Sintering Plus Annealing

Synthesis and Properties of an Ultrafine Grained Ti-45al-2cr-2nb-1b-0.5ta Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

Microstructures and Mechanical Properties of TiAl Alloy Prepared by Spark Plasma Sintering

Preparation of Ti-45Al-5.5(Cr,Nb,B,Ta) Alloy by Mechanical Milling and Spark Plasma Sintering

Achieving synergy enhancement of strength and ductility in Ti-6Al-2Sn-4Zr-2Mo-0.1Si alloy by fabricating a new multiscale microstructure

Fabrication of ultrafine grained FeCrAl-0.6 wt.% ZrC alloys with enhanced mechanical properties by spark plasma sintering

Superior mechanical properties of a selective-laser-melted AlZnMgCuScZr alloy enabled by a tunable hierarchical microstructure and dual-nanoprecipitation

Microstructure Evolution and Mechanical Properties of ODS FeCrAl Alloys Fabricated by Spark Plasma Sintering

Super High Strength Aluminum Alloy Processed By Mechanical Alloying And Hot Extrusion

Tailoring Hierarchical Microstructures and Nanoprecipitates in Additive-Manufactured Al-Zn-Mg-Cu-Nb Alloys for Simultaneously Enhancing Strength and Ductility

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

A Novel Method for the Preparation of Heterostructures 5083 Aluminum Alloys to Enhancing Comprehensive Mechanical Properties

Microstructure and mechanical properties of Ti-43Al-9V alloy fabricated by spark plasma sintering