Abstract:Due to the rapid sintering and densification, spark plasma sintering (SPS) technology can significantly inhibit grain coarsening, and obtain alloy with high density and uniform microstructure. Tantalum-tungsten (Ta-W) alloy had been fabricated by powder metallurgy and consolidated by SPS at temperature of 1600 °C for 5 min at the pressure of 35 MPa. Specimens of pure Ta and four tantalum-based alloys with different concentrations of tungsten ranging from 2.5 to 10 were used to investigate the behavior of developed alloys. X-ray diffraction analyses were applied for all compositions of Ta-W alloys. The morphology of fracture sections was analyzed by scanning electron microscopy (SEM). Morphologies of initial Ta and W powders, microstructures of sintering Ta-W alloy and tensile fractographs of the specimens with different components were observed. When the concentrations of tungsten were distributed with 2.5 wt%, 5 wt%, 7.5 wt% and 10 wt%, the measured densities were 16.151 g/cm3, 15.756 g/cm3, 15.711 g/cm3, 15.665 g/cm3 and 15.670 g/cm3 respectively. As the content of tungsten increased, the density of the alloy decreased and the grain was refined, meanwhile the micro-hardness of the samples increased gradually. Furthermore, the addition of tungsten could greatly enhance the strength of the alloys, but decrease the plasticity of the alloys. Ta-2.5 wt%W shows the maximum bending strength with a value of 832.29 MPa, while the percentage of transgranular fracture increased with the increase of tungsten content.

Phase, Microstructure and Properties Evolution of Fine-Grained W–Mo–Ni–Fe Alloy During Spark Plasma Sintering

Microstructure and mechanical properties of fine-grained W-7Ni-3Fe heavy alloy by spark plasma sintering

Microstructure, Phase Transformation and Mechanical Property of Ni-Co-Mn-In Alloy Prepared by Spark Plasma Sintering

Microstructure and mechanical properties of liquid–phase sintered W@NiFe composite powders

Effects of Sintering Temperature on Fine-Grained Tungsten Heavy Alloy Produced by High-Energy Ball Milling Assisted Spark Plasma Sintering

Evolution from Amorphous to Nanocrystalline and Corresponding Magnetic Properties of Fe-Si-B-Cu-Nb Alloys by Melt Spinning and Spark Plasma Sintering

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Effects of in situ phase reaction of η M12C and M6C on microstructure and mechanical properties of tungsten heavy alloy via spark plasma sintering

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

Microstructural Evolution and Mechanical Properties of Spark Plasma Sintering of Tantalum-Tungsten Alloy

Ultrafine Grain Tungsten Heavy Alloys with Excellent Performance Prepared by Spark Plasma Sintering

Development and Characterization of a Novel Fine-Grained W–Ni–Mn–Mo Alloys with La2O3 Addition Prepared Via Low-Temperature Sintering

The effect of fine W particles in matrix phase on mechanical properties of tungsten heavy alloys

Study on the process and microstructure of Fe34Mn13.5Al3Cr7.5Ni alloy prepared by spark plasma sintering based on elemental powder

Alloying behavior of W and Mo in the as-cast dual-phase FeNiCrAl multi-component alloys

Microstructure, Densification and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated by Spark Plasma Sintering

Spark Plasma Sintering of W-10Ti Alloys: Microstructure, Properties and Grain Growth Kinetics

Phase Evolution of Mo-W-Cu Alloy Rapid Prepared by Spark Plasma Sintering

The process and mechanical properties of Nb–Si–Mo–Ti alloy prepared by spark plasma sintering

A novel dissolution-precipitation mechanism during liquid phase sintering and its strengthening effects in W-Ni-Fe alloys with low W contents

Effect of Tungsten on Microstructure and Mechanical Properties of Novel NiMnCrMoWx High-Entropy Alloys Developed by Mechanical Alloying