Abstract:Development of proton exchange membranes (PEMs) with low methanol permeability and high ionic conductivity is an effective way to improve the lifespan and power density of direct methanol fuel cells (DMFCs). Here, we report a novel phosphoric acid (PA)-doped quaternary ammonium ion-modified poly (vinylidene fluoride) nanofiber composite PEM (QA@PVDF/SPEEK-PA) for DMFCs. Benefiting from the rich acid-base ion-pair interface (–NH 2 /-N(CH 3 ) 3 + and −SO 3 H/H 2 PO 4 - ) constructed within the membrane, QA@PVDF/SPEEK-PA exhibited an ultrahigh conductivity of up to 202.31 mS cm −1 at 80 °C, corresponding to 2.6 and 1.31 times the conductivity of SPEEK (77.8 mS cm −1 ) and commercial Nafion 211 (154.03 mS cm −1 ), respectively. More importantly, the introduction of 3D nanofibers within the membrane together with the formation of acid-base interactions led to the excellent methanol barrier effect over a wide methanol range. Even with a 10 M CH 3 OH fuel, the cross-current density of methanol remained at a mere 161.21 mA cm −2 , while the open-circuit voltage (OCV) of the fuel cell reached an impressive 0.73 V. The DMFC assembled with the membrane exhibited a peak power density (PPD) of 121.38 mW cm −2 , representing a 1.36-fold relative to that of Nafion 211. After 260 h of in-situ durability test, the OCV was reduced by only 7.49 %. These excellent results suggest that the PA-doped nanofiber composite PEMs are promising candidates for future DMFCs applications.

A Neat Methanol Fed Passive DMFC with a New Anode Structure

Novel Anode Electrode Structure with a Fuel Management Layer for High-Concentration Passive Direct Methanol Fuel Cells

A Passive Vapor-Feed Direct Methanol Fuel Cell Based on a Composite Pervaporation Membrane

Mechanically Robust and Highly Methanol-Resistant Sulfonated Poly(ether Ether Ketone)/poly(vinylidene Fluoride) Nanofiber Composite Membranes for Direct Methanol Fuel Cells

A Methanol Fuel Processing System with Methanol Steam Reforming and CO Selective Methanation Modules for PEMFC Application

Design, Optimization and Microfabrication of a Micro-Direct Methanol Fuel Cell with Microblocks in Anode Structure

A Study of the Direct Dimethyl Ether Fuel Cell Using Alkaline Anolyte

Improvement of Direct Methanol Fuel Cell Performance by Modifying Catalyst Coated Membrane Structure

Development of MEMS-based direct methanol fuel cell with high power density using nanoimprint technology

A High-Performance Direct Methanol Fuel Cell Technology Enabled by Mediating High-Concentration Methanol Through a Graphene Aerogel

An Air-Breathing Micro Direct Methanol Fuel Cell with 3D KOH-Etched Cathode Structure

Influence of intermediate liquid electrolyte layer on the performance of passive direct methanol fuel cell

PA-doped nanofiber composite proton exchange membranes with ultrahigh proton conductivity and methanol barrier performance for direct methanol fuel cells

Optimization of Membrane Electrode Assembly in Air-Breathing Direct Methanol Fuel Cell

Design and Fabrication of a Polymer-Based Micro Direct Methanol Fuel Cell

Passive Fuel Delivery Based on Hydrophobic Porous Silicon for Micro Direct Methanol Fuel Cells

Influence of Current Collector Design and Combination on the Performance of Passive Direct Methanol Fuel Cells

Numerical simulation on mass transport in a passive vapor-fed direct methanol fuel cell operating with neat methanol

Composite Membranes from Quaternized Chitosan Reinforced with Surface-Functionalized PVDF Electrospun Nanofibers for Alkaline Direct Methanol Fuel Cells

Effect of Methanol Concentration on Performance of Passive DMFC

Constructing a graphene-contained layer in anode to improve the performance of direct methanol fuel cells using high-concentration fuel