Abstract:The fabrication art of the membrane electrode assembly (MEA) in a proton-exchange membrane (PEM) fuel cell strongly correlates to the cell performance. It has been recognized that defects, for example, high interfacial resistance between the catalyst layers (CLs) and the membrane or cracks in the CLs, may occur during the MEA manufacturing process. These defects could greatly influence the electrochemical performance of the fuel cell. To eliminate those defects and improve the cell performance, in this study, a novel fabrication approach of the MEA for PEM fuel cells is developed. With this method, the Nafion ionomer, employed as a PEM, is directly coated onto both the cathode and anode CLs. As a result, not only an excellent interfacial connection between the PEM and CLs is achieved with a low interfacial resistance, but also cracks are eliminated due to Nafion ionomer penetration into the cracks, forming hydrophilic channels with ionic conduction. Those ionic conduction channels improve the water management, lower the mass transport loss, and facilitate the proton transfer, thus maximizing the three-phase boundary and enhancing the utilization of Pt/C catalysts. By adding an expanded polytetrafluoroethylene film, a favorable mechanical property of the MEA is also achieved. This novel MEA exhibits excellent cell performance under low humidity conditions. Under the H<sub>2</sub>/air operation, the cell performance reaches a high maximum power density of 1.35 W cm<sup>–2</sup>.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acssuschemeng.0c02386?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acssuschemeng.0c02386</a>.SEM images, photographs of MEAs and fitted impedance parameters for the MEAs (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.0c02386/suppl_file/sc0c02386_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Optimization of Membrane Electrode Assembly in Air-Breathing Direct Methanol Fuel Cell

Improvement of Direct Methanol Fuel Cell Performance by Modifying Catalyst Coated Membrane Structure

Development of Cathode Ordered Membrane Electrode Assembly Based on TiO2 Nanowire Array and Ultrasonic Spraying

Novel Anode Electrode Structure with a Fuel Management Layer for High-Concentration Passive Direct Methanol Fuel Cells

Performance of an integrated composite membrane electrode assembly in DMFC

Anode Sub-Layer in Membrane Electrode Assembly of DMFC

Critical materials and technology in direct methanol fuel cells

Optimizing proton exchange membrane fuel cell performance at low-humidity via constructing additional anodic water-retaining membrane layer containing sulfonated multi-walled carbon nanotubes

Preparation and Simulation of an Additional Catalyst Layer for Direct Methanol Fuel Cell

A Novel Approach to Fabricate Membrane Electrode Assembly by Directly Coating the Nafion Ionomer on Catalyst Layers for Proton-Exchange Membrane Fuel Cells

Influence of intermediate liquid electrolyte layer on the performance of passive direct methanol fuel cell

Structural optimization and performance trade-off strategies for semi-crystalline sulfonated poly(arylene ether ketone) membranes in high-concentration direct methanol fuel cells

Development of MEMS-based direct methanol fuel cell with high power density using nanoimprint technology

The Performance Improvement of Membrane and Electrode Assembly in Open-Cathode Proton Exchange Membrane Fuel Cell

Optimization of Membrane Electrode Assembly of PEM Fuel Cell by Response Surface Method

A High-Performance Direct Methanol Fuel Cell Technology Enabled by Mediating High-Concentration Methanol Through a Graphene Aerogel

Optimization of Multiple Reactants in a Membrane-Less Direct Methanol Fuel Cell (DMFC)

A Neat Methanol Fed Passive DMFC with a New Anode Structure

Effect of Methanol Concentration on Performance of Passive DMFC

Influence of liquid electrolyte and liquid flowing electrolyte on the performance of an air breathing direct methanol fuel cell (ABDMFC)

A Liquid–Vapor Two-Phase Model of Direct Methanol Fuel Cells With Platinum Group Metal-Free Cathode Catalyst