Abstract:The fabrication art of the membrane electrode assembly (MEA) in a proton-exchange membrane (PEM) fuel cell strongly correlates to the cell performance. It has been recognized that defects, for example, high interfacial resistance between the catalyst layers (CLs) and the membrane or cracks in the CLs, may occur during the MEA manufacturing process. These defects could greatly influence the electrochemical performance of the fuel cell. To eliminate those defects and improve the cell performance, in this study, a novel fabrication approach of the MEA for PEM fuel cells is developed. With this method, the Nafion ionomer, employed as a PEM, is directly coated onto both the cathode and anode CLs. As a result, not only an excellent interfacial connection between the PEM and CLs is achieved with a low interfacial resistance, but also cracks are eliminated due to Nafion ionomer penetration into the cracks, forming hydrophilic channels with ionic conduction. Those ionic conduction channels improve the water management, lower the mass transport loss, and facilitate the proton transfer, thus maximizing the three-phase boundary and enhancing the utilization of Pt/C catalysts. By adding an expanded polytetrafluoroethylene film, a favorable mechanical property of the MEA is also achieved. This novel MEA exhibits excellent cell performance under low humidity conditions. Under the H<sub>2</sub>/air operation, the cell performance reaches a high maximum power density of 1.35 W cm<sup>–2</sup>.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acssuschemeng.0c02386?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acssuschemeng.0c02386</a>.SEM images, photographs of MEAs and fitted impedance parameters for the MEAs (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.0c02386/suppl_file/sc0c02386_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Performance of an integrated composite membrane electrode assembly in DMFC

Optimization of Membrane Electrode Assembly in Air-Breathing Direct Methanol Fuel Cell

Development of Cathode Ordered Membrane Electrode Assembly Based on TiO2 Nanowire Array and Ultrasonic Spraying

Development of MEMS-based direct methanol fuel cell with high power density using nanoimprint technology

Improvement of Direct Methanol Fuel Cell Performance by Modifying Catalyst Coated Membrane Structure

Mechanically Robust and Highly Methanol-Resistant Sulfonated Poly(ether Ether Ketone)/poly(vinylidene Fluoride) Nanofiber Composite Membranes for Direct Methanol Fuel Cells

A Novel Approach to Fabricate Membrane Electrode Assembly by Directly Coating the Nafion Ionomer on Catalyst Layers for Proton-Exchange Membrane Fuel Cells

Critical materials and technology in direct methanol fuel cells

A Neat Methanol Fed Passive DMFC with a New Anode Structure

Performance Enhancement of Polymer Electrolyte Membrane with Nano-Calcium Carbonate Prepared by Mechanochemical for Direct Methanol Fuel Cell Applications

The fabrication of integrated proton exchange membrane fuel cells: Excellent mechanical strength and electrochemical performance

A High-Performance Direct Methanol Fuel Cell Technology Enabled by Mediating High-Concentration Methanol Through a Graphene Aerogel

PA-doped nanofiber composite proton exchange membranes with ultrahigh proton conductivity and methanol barrier performance for direct methanol fuel cells

Anode Sub-Layer in Membrane Electrode Assembly of DMFC

A cost-effective and highly efficient dissymmetric membrane electrode assembly designed for fuel cells

Design and Fabrication of a Polymer-Based Micro Direct Methanol Fuel Cell

Polyelectrolyte Membranes Based on Nafion/Chitosan Blends for Direct Methanol Fuel Cell Application

Effect of Methanol Concentration on Performance of Passive DMFC

Grafted polymer electrolyte membrane for direct methanol fuel cells

Novel sepiolite reinforced emerging composite polymer electrolyte membranes for high-performance direct methanol fuel cells

A Novel Assembly Method for a Micro Direct Methanol Fuel Cell Using Multi-Layer Bonding Technique