Abstract:Surface acoustic waves (SAWs) are of practical importance across several fields. Particularly, a wide range of SAW devices is available, which are based on the stacking piezoelectric layered hetero-structures. As such, efficient and stable algorithm of analyzing electromechanical coupling factor (K2) should be of specific interest, inspiring a variety of piezoelectric layered structures. Motivated by the above considerations, this paper exploits the performance of Sc43% AlN57%/ZnO/diamond piezoelectric hetero-structures using matrix and polynomial methods. Consequently, dispersion curves, the electromechanical coupling factor and profiles of Rayleigh waves are calculated, in which the properties of hexagonal intermediate ZnO layer are varied. Here, $$ (0001) - [10\bar{1}0]{\text{ZnO}} $$ or $$ (11\bar{2}0) - [0001]{\text{ZnO}} $$ directions of the middle layer were integrated with Sc43% AlN57%/diamond to be a composite hetero-structure with a larger K2 of SAW. Accordingly, a commercial ZnO specimen was characterized by scanning electron microscopy (SEM) as well as Raman and XRD spectroscopy to determine its available crystallographic directions and the C-axis hexagonal character. Comparing with conventional AlN/diamond hetero-structures, the inclusion of ZnO as the intermediate layer provides with an excellent electromechanical coupling factor which significantly improves the $$ (11\bar{2}0) - [0001] $$ structure. However, comparing with the ZnO/diamond hetero-structure, a high phase velocity (Vph) was observed. Therefore, the development of a well-balanced structure that maximizes the values of Vph and K2 is systematically challenging. Moreover, it was found that initial stresses have a significant effect on the Rayleigh wave velocities. Fundamental A0 Lamb mode can be generated in piezoelectric hetero-structures when the properties of substrate remain very low relative to the film. Numerical results obtained in this paper can provide a deeper insight into the nature of the Rayleigh wave behaviors in piezoelectric hetero-structures, involving a ZnO intermediate layer.

ZnO thin film piezoelectric micromachined microphone with symmetric composite vibrating diaphragm

Influence of Stress on the Performance of PZT Thin Films for Microphone Application

Theoretical study on design of ZnO piezoelectric thin film sensors

Experimental Study of High-Frequency Vibration Assisted Micro/Meso-Scale Forming of Metallic Materials

On the Performance Enhancement of Piezoelectric MEMS Microphone Using S-Shape Slit Design

Study on technology of zinc oxide piezoelectric thin film device with surface micromachining substrate

Fabrication of high-quality PZT-based piezoelectric microphone

Piezoelectric Micromachined Microphone with High Acoustic Overload Point and with Electrically Controlled Sensitivity

High Sensitivity and High S/N Microphone Achieved by PZT Film with Central-Circle Electrode Design

Fabrication of a Cantilever Structure for Piezoelectric Microphone

A Novel Structure for Pzt-Based Piezoelectric Microphone

Optimization of magnetoimpedance and stress-impedance effects in single-microwire polymer composites for stress monitoring

Micro Acoustic Devices Using Piezoelectric Films

A piezoelectric micro-electromechanical microphone for implantable hearing aid applications

Design, fabrication and reliability study of piezoelectric ZnO based structure for development of MEMS acoustic sensor

Influence of Buffer Layers on the Piezoelectric Property of ZnO Film

Micromachined Piezoelectric Acoustic Device

FABRICATION AND PROPERTIES OF A MICROSTRAIN SENSOR BASED ON ZINC OXIDE NETWORK STRUCTURE

Design of Cantilever Diaphragm Array Piezoelectric MEMS Microphone for Signal-To-Noise Ratio Enhancement

Influence of a Piezoelectric ZnO Intermediate Layer on Rayleigh Waves Propagating in Sc 43% AlN 57% /zno/diamond Hetero-Structures Subjected to Uniaxial Stress

Design And Fabrication of Condenser Microphone Using Wafer Transfer And Micro-electroplating Technique