Abstract:We report an industrial compatible tunnel oxide passivated contact (TOPCon) structure on solar-grade p-type c-Si wafer as the rear emitter for high-efficiency solar cells, where the ultrathin silicon oxide (SiOx) is made by plasma-assisted oxidation and the P-doped n-type poly-Si (n+-poly-Si) contact layer by plasma-enhanced chemical vapor deposition (PECVD) of hydrogenated amorphous silicon (a-Si:H) with in-situ doping with PH3 and following the high-temperature annealing. The fabrication processes of SiOx and n+-poly-Si layers are systematically optimized. It is found that the optimized annealing temperature for the crystallization and dopant activation is in the range of 850 °C and 880 °C, which is higher than the similar structure with chemically oxidized SiOx (820 °C). In addition, the samples made with higher PH3/SiH4 doping ratio during the a-Si:H deposition need a lower annealing temperature to reach the similar dopant distribution within the samples made with lower doping ratio but annealed at higher temperature, it means that the optimized annealing temperature decreases with the increase of the PH3/SiH4 doping ratio during the deposition of a-Si:H precursor. The optimized process with post-hydrogenation yields excellent surface passivation on the p-type Si substrate with the implied open-circuit voltage (iVoc) of ∼742 mV, the single-side saturated recombination current density (J0) of ∼3.0 fA/cm2, the contact resistivity (ρc) of ∼2–4 mΩ cm2, and the effective minority carrier lifetime (τeff) of ∼1050 μs (Δn = 1 × 1015 cm-3). With these passivation parameters, a simulation study demonstrates the advantage of rear emitter over the conventional front emitter TOPCon solar cell with ∼22.8% achievable efficiency on solar-grade p-type wafers with current industrial constraints, and ∼24.9% on high quality p-type c-Si wafers with the optimized conditions in R&D laboratories. Our study suggests that the p-type c-Si solar cell with a rear n+-poly-Si TOPCon emitter is a viable structure for high-efficiency solar cell production.

Thin Al2O3 passivated boron emitter of n-type bifacial c-Si solar cells with industrial process

Fully screen-printed bifacial large area 22.6% N-type Si solar cell with lightly doped ion-implanted boron emitter and tunnel oxide passivated rear contact

n-Type polysilicon passivating contact for industrial bifacial n-type solar cells

High-efficiency N-Type Silicon PERT Bifacial Solar Cells with Selective Emitters and Poly-Si Based Passivating Contacts

Impact of Boron Doping Concentration on Tunnel Oxide Passivated Contact in Front Surface for N-Type Poly-Si Based Passivated Contact Bifacial Solar Cells

Application of SiO2 Passivation Technique in Mass Production of Silicon Solar Cells

The 18.3% Silicon Solar Cells with Nano-Structured Surface and Rear Emitter

21.3%-Efficient N-Type Silicon Solar Cell with a Full Area Rear TiOx/LiF/Al Electron-Selective Contact

Fast Co‐Diffusion Process for Bifacial n‐Type Solar Cells

SiO 2 Passivation Layer Grown by Liquid Phase Deposition for N-type Bifacial Silicon Solar Cells

Approaching 23% with large‐area monoPoly cells using screen‐printed and fired rear passivating contacts fabricated by inline PECVD

Bifacial p-Type PERC Solar Cell with Efficiency over 22% Using Laser Doped Selective Emitter

Presented at the 31st European PV Solar Energy Conference and Exhibition, 14-18 September 2015, Hamburg, Germany OPTIMIZATION OF BBr3 DIFFUSION PROCESSES FOR N-TYPE SILICON SOLAR CELLS

Three-Step Process for Efficient Solar Cells with Boron-Doped Passivated Contacts

Efficiency improvement of crystalline silicon solar cells with a back-surface field produced by boron and aluminum co-doping

An industrially viable TOPCon structure with both ultra-thin SiOx and n+-poly-Si processed by PECVD for p-type c-Si solar cells

Bifacial silicon heterojunction solar cells using transparent‐conductive‐oxide‐ and dopant‐free electron‐selective contacts

Enhanced passivation and stability of negative charge injected SiN x with higher nitrogen content on the boron diffused surface of n-type Si solar cells

Towards Thinner and Low Bowing Silicon Solar Cells: Form the Boron and Aluminum Co‐doped Back Surface Field with Thinner Metallization Film

Low Recombination Firing-Through Al Paste for N-Type Solar Cell with Boron Emitter

24.2% efficient POLO back junction solar cell with an AlOx/SiNy dielectric stack from an industrial‐scale direct plasma‐enhanced chemical vapor deposition system