Abstract:Crystalline silicon (c-Si) solar cells with passivation stacks consisting of a polycrystalline silicon (poly-Si) layer and a thin interfacial silicon dioxide (SiO2) layer show high conversion efficiencies. Since the poly-Si layer in this structure acts as a carrier transport layer, high doping of the poly-Si layer is crucial for high conductivity and the efficient transport of charge carriers from the bulk to a metal contact. In this respect, conventional furnace-based high-temperature doping methods are limited by the solid solubility of the dopants in silicon. This limitation particularly affects p-type doping using boron. Previously, we showed that laser activation overcomes this limitation by melting the poly-Si layer, resulting in an active concentration beyond the solubility limit after crystallization. High electrically active boron concentrations ensure low contact resistivity at the (contact) metal/semiconductor interface and allow for the maskless patterning of the poly-Si layer by providing an etch-stop layer in an alkaline solution. However, the high doping concentration degrades during long high-temperature annealing steps. Here, we performed a test of the stability of such a high doping concentration under thermal stress. The active boron concentration shows only a minor reduction during SiNx:H deposition at a moderate temperature and a fast-firing step at a high temperature and with a short exposure time. However, for an annealing time tanneal = 30 min and an annealing temperature 600 °C ≤ Tanneal≤ 1000 °C, the high conductivity is significantly reduced, whereas a high passivation quality requires annealing in this range. We resolve this dilemma by introducing a second, healing laser reactivation step, which re-establishes the original high conductivity of the boron-doped poly-Si and does not degrade the passivation. After a thermal annealing temperature Tanneal = 985 °C, the reactivated layers show high sheet conductance (Gsh) with Gsh = 24 mS sq and high passivation quality, with the implied open-circuit voltage (iVOC) reaching iVOC = 715 mV. Therefore, our novel three-step process consisting of laser activation, thermal annealing, and laser reactivation/healing is suitable for fabricating highly efficient solar cells with p++-poly-Si/SiO2 contact passivation layers.

Presented at the 31st European PV Solar Energy Conference and Exhibition, 14-18 September 2015, Hamburg, Germany OPTIMIZATION OF BBr3 DIFFUSION PROCESSES FOR N-TYPE SILICON SOLAR CELLS

Empirical optimization and implementation of boron emitter on n-type silicon solar cells using BBR3 liquid source

Borosiloxane boron diffusion for p-emitter formation on n-type silicon wafers

Boron tube diffusion process parameters for high-efficiency n-TOPCon solar cells with selective boron emitters

Influence of boron doping profile on emitter and metal contact recombination for n-PERT silicon solar cells

Emitter formation with boron diffusion from PECVD deposited boron-doped silicon oxide for high-efficiency TOPCon solar cells

Three-Step Process for Efficient Solar Cells with Boron-Doped Passivated Contacts

Impact of boron doping on electrical performance and efficiency of n-TOPCon solar cell

Plasma‐immersion ion implantation: A path to lower the annealing temperature of implanted boron emitters and simplify PERT solar cell processing

A Novel Processing Technology for High‐Efficiency Silicon Solar Cells

Optimization of efficiency enhancement of TOPCon cells with boron selective emitter

Superb improvement of boron doping in selective emitter for TOPCon solar cells via boron-doped silicon paste

Impact of Boron Doping Concentration on Tunnel Oxide Passivated Contact in Front Surface for N-Type Poly-Si Based Passivated Contact Bifacial Solar Cells

Efficiency improvement of crystalline silicon solar cells with a back-surface field produced by boron and aluminum co-doping

Electrical Deactivation of Boron in p+-Polycrystalline Silicon/SiOx/Crystalline Silicon Passivating Contacts for Silicon Solar Cells

Study on selective emitter fabrication through an innovative pre‐diffusion process for enhanced efficiency in TOPCon solar cells

Boron-doping of cubic SiC for intermediate band solar cells: a scanning transmission electron microscopy study

Tracing the boron diffusion into a textured silicon solar cell by combining boron diffusion simulation with experimental and simulated scanning transmission electron beam induced current

A Novel Strategy for Preparing a Selective Back Surface Field of N-Type Emitter Wrap Through Solar Cells

n-Type polysilicon passivating contact for industrial bifacial n-type solar cells

Low Recombination Firing-Through Al Paste for N-Type Solar Cell with Boron Emitter