Abstract:A new sulfurization configuration is elaborated, and suitable parameters are explored for the preparation of Cu2CdSnS4 thin films. Appropriate copper content can reduce the fluctuations of bandgap and electrostatic potential in Cu2CdSnS4 thin film. The best efficiency of Cu2CdSnS4 thin film solar cell can be found over 10% efficient under the ratio of 0.83 and 590 °C sulfurization temperature. At present, Kesterite‐based thin‐film solar cells, such as Cu2ZnSnS4 solar cells, involve serious band‐tailed states, which leads to low open‐circuit voltage, thereby hindering the further improvement of device performance. In stannite‐based materials, such as Cu2CdSnS4, the substitution of Zn with Cd can effectively suppress CuCd‐related point defects and defect clusters; thus, the band‐tailing state is few, which has attracted considerable research attention. In this work, on the basis of using optimized sulfurization and optimizing ratios (Cu/Cd+Sn) and temperatures, Cu2CdSnS4 thin films can be obtained with good quality and single‐phase composition, in which the device prepared at a ratio of 0.83 and 590 °C has the highest efficiency. Defect analysis shows that the substitution of Zn with Cd can effectively reduce CuCd‐related defects and defect clusters (such as 2CuCd+SnCd) and also decrease Urbach energy, fluctuations of bandgap, and electrostatic potential compared with kesterite‐based devices. In particular, Cu2CdSnS4 thin‐film solar cell prepared under optimized conditions (the ratio of 0.83 and 590 °C) has the minimum reverse saturation current, red shift, and the maximum minority carrier diffusion length. Therefore, an efficiency over 10% Cu2CdSnS4 thin‐film solar cell is reported, which shows the highest efficiency among stannite‐based solar cells to date.

Large Voc Improvement and 9.2% Efficient Pure Sulfide Cu2ZnSnS4 Solar Cells by Heterojunction Interface Engineering

Synergetic Effects of Zn Alloying and Defect Engineering on Improving the CdS Buffer Layer of Cu2ZnSnS4 Solar Cells

Further studies in body fluid metabolism. II. The relative efficacy in man of sodium bicarbonate and sodium lactate as alkalizing compounds, and of ammonium chloride and hydrochloric acid as acidifying compounds.

Toward High Efficient Cu2 ZnSn(Sx ,Se1- x )4 Solar Cells: Break the Limitations of VOC and FF

CdS(In)/CZTSSe bandgap alignment engineering for performance enhancement of solar cells without ZnO layer

Calcium-regulated parathyroid hormone release in primary hyperparathyroidism: studies in vitro with dispersed parathyroid cells.

Improving the efficiency of Cu2ZnSnS4 solar cells by promoting the homogeneous distribution of Sn element

Cd‐Free Pure Sulfide Kesterite Cu2ZnSnS4 Solar Cell with Over 800 mV Open‐Circuit Voltage Enabled by Phase Evolution Intervention

Cu2ZnSnS4 solar cells with over 10% power conversion efficiency enabled by heterojunction heat treatment

Li-based Selenized Cu2ZnSnS4 Surface: Possible Route to Overcoming Voc-Deficit of Kesterite Solar Cells

Interface Recombination of Cu 2 ZnSnS 4 Solar Cells Leveraged by High Carrier Density and Interface Defects

Elemental de-mixing-induced epitaxial kesterite/CdS interface enabling 13%-efficiency kesterite solar cells

Gradient bandgap enables >13% efficiency sulfide Kesterite solar cells with open-circuit voltage over 800 mV

Realizing zinc-doping of CdS buffer layer via partial electrolyte treatment to improve the efficiency of Cu2ZnSnS4 solar cells

Heterojunction post-heat treatment process driving high efficiency for Cu2ZnSnS4 solar cell

Over 10% Efficient Cu2CdSnS4 Solar Cells Fabricated from Optimized Sulfurization

Se as hetero-nucleation seeds reinforcing intermetallic diffusion for improved electrodeposition-processed CZTS solar cells

12.3% Efficient Low Voc Loss Pure Sulfide Kesterite Solar Cells from DMSO Solution via Cadmium Alloying

Energy Band Alignment at p-n Heterojunction Interface in CZTSSe Solar Cells with Novel ZnMgO Buffer Layer

Interface band gap narrowing behind open circuit voltage losses in Cu$_2$ZnSnS$_4$ solar cells

Suppressing Element Inhomogeneity Enables 14.9% Efficiency CZTSSe Solar Cells