Abstract:A new sulfurization configuration is elaborated, and suitable parameters are explored for the preparation of Cu2CdSnS4 thin films. Appropriate copper content can reduce the fluctuations of bandgap and electrostatic potential in Cu2CdSnS4 thin film. The best efficiency of Cu2CdSnS4 thin film solar cell can be found over 10% efficient under the ratio of 0.83 and 590 °C sulfurization temperature. At present, Kesterite‐based thin‐film solar cells, such as Cu2ZnSnS4 solar cells, involve serious band‐tailed states, which leads to low open‐circuit voltage, thereby hindering the further improvement of device performance. In stannite‐based materials, such as Cu2CdSnS4, the substitution of Zn with Cd can effectively suppress CuCd‐related point defects and defect clusters; thus, the band‐tailing state is few, which has attracted considerable research attention. In this work, on the basis of using optimized sulfurization and optimizing ratios (Cu/Cd+Sn) and temperatures, Cu2CdSnS4 thin films can be obtained with good quality and single‐phase composition, in which the device prepared at a ratio of 0.83 and 590 °C has the highest efficiency. Defect analysis shows that the substitution of Zn with Cd can effectively reduce CuCd‐related defects and defect clusters (such as 2CuCd+SnCd) and also decrease Urbach energy, fluctuations of bandgap, and electrostatic potential compared with kesterite‐based devices. In particular, Cu2CdSnS4 thin‐film solar cell prepared under optimized conditions (the ratio of 0.83 and 590 °C) has the minimum reverse saturation current, red shift, and the maximum minority carrier diffusion length. Therefore, an efficiency over 10% Cu2CdSnS4 thin‐film solar cell is reported, which shows the highest efficiency among stannite‐based solar cells to date.

Cu2ZnSnS4 solar cells with over 10% power conversion efficiency enabled by heterojunction heat treatment

Heterojunction post-heat treatment process driving high efficiency for Cu2ZnSnS4 solar cell

Elemental de-mixing-induced epitaxial kesterite/CdS interface enabling 13%-efficiency kesterite solar cells

Over 10% Efficiency Pure Sulfide Kesterite Solar Cells on Transparent Electrode with Cd-Ag Co-Alloying

Over 10% Efficient Cu2CdSnS4 Solar Cells Fabricated from Optimized Sulfurization

Cd‐Free Pure Sulfide Kesterite Cu2ZnSnS4 Solar Cell with Over 800 mV Open‐Circuit Voltage Enabled by Phase Evolution Intervention

Defect Control for 12.5% Efficiency Cu2ZnSnSe4 Kesterite Thin-Film Solar Cells by Engineering of Local Chemical Environment

Gradient bandgap enables >13% efficiency sulfide Kesterite solar cells with open-circuit voltage over 800 mV

Defect Control for 12.5% Efficiency Cu2 ZnSnSe4 Kesterite Thin-Film Solar Cells by Engineering of Local Chemical Environment

Realization of 11.5% Efficiency Cu 2 ZnSn(S,Se) 4 Thin‐Film Solar Cells by Manipulating the Phase Structure of Precursor Films

Toward High Efficient Cu2 ZnSn(Sx ,Se1- x )4 Solar Cells: Break the Limitations of VOC and FF

High Efficiency Cu 2 ZnSn(S,Se) 4 Solar Cells with Shallow Li Zn Acceptor Defects Enabled by Solution‐Based Li Post‐Deposition Treatment

10.24% Efficiency of Flexible Cu2 ZnSn(S,Se)4 Solar Cells by Pre-Evaporation Selenization Technique

High Efficiency Cu2ZnSn(S,Se)4 Solar Cells with Shallow LiZn Acceptor Defects Enabled by Solution‐Based Li Post‐Deposition Treatment

Cu2ZnSnSSe4 Solar Cells with 9.6% Efficiency Via Selenizing Cu-Zn-Sn-S Precursor Sputtered from a Quaternary Target

All Solution-Processed Cu2znsns4 Solar Cell By Using High-Boiling-Point Solvent Treated Ball-Milling Process With Efficiency Exceeding 6%

Optimization of the Selenization Pressure Enabling Efficient Cu 2 ZnSn(S,Se) 4 Solar Cells

Improving the efficiency of Cu2ZnSnS4 solar cells by promoting the homogeneous distribution of Sn element

All-Layer Sputtering-Free Cu2Zn1-xCdxSnS4 Solar Cell with Efficiency Exceeding 7.5%

Unveiling the Selenization Reaction Mechanisms in Ambient Air-Processed Highly Efficient Kesterite Solar Cells

Cu2ZnSn(S, Se)4 solar cell with slight band tailing states achieves 11.83% efficiency by selenizing sputtered Cu–Zn–Sn–S precursor