Abstract:A potentially manufacturable liquid‐source MOCVD process was applied to deposit platinum (Pt) films (12–140 nm) on thermally oxidized Si substrates. The deposition of Pt films was carried out at a substrate temperature of 350 °C by oxygen‐assisted pyrolysis of complex precursors in a low‐pressure, hot‐wall reactor. The effects of two different metal–organic precursors, a) trimethyl methyl cyclopentadienyl platinum [(CH3)3CH3CpPt], and b) platinum acetylacetonate [Pt(acac)2], on the properties of Pt films were studied. Although the polycrystalline Pt films deposited from Pt(acac)2 exhibited a preferred (111) orientation with a X‐ray intensity ratio of I(111)/I(200) = 40, the films deposited from (CH3)3CH3CpPt were highly (111) oriented with I(111)/I(200) = 270. The following properties were typical of Pt films from Pt(acac)2 as compared to Pt films from (CH3)3CH3CpPt: finer grain size (25 nm vs. 50 nm), smaller root mean square (rms) surface roughness (5 nm vs. 15 nm), and better step coverage (95 % vs. 35 %). These experimental findings indicated that growth of Pt films from Pt(acac)2 occurred under the kinetically‐limited regime, whereas the deposition of Pt from (CH3)3CH3CpPt was limited by the mass transport rate. Additionally, the temperature (4.2–293 K) dependence of the electrical resistivities (ρ) of Pt films was measured and the electron mean free paths were estimated. It was observed that ρ(T) deviated from Matthiessen's rule. Platinum thin films are grown on thermal‐SiO2/Si at 350 °C from (CH3)3‐CH3CpPt and Pt(acac)2. Films deposited from the first precursor show an orientation ratio of [I(111)/I(200) = 270], a large grain size of 50 nm, and poor conformality of 35–45 %, while those produced from Pt(acac)2 show [I(111)/I(200) = 40], finer grain structure, and excellent conformality of 85–95 % (see Figure). Film resistivity exhibits values of 23.6 and 27.6 μΩ cm.

Plasma Enhanced Atomic Layer Deposited Platinum Thin Film on Si Substrate with Tma Pretreatment

Effect of Trimethyl Aluminium Surface Pretreatment on Atomic Layer Deposition Al2o3 Ultra-Thin Film on Si Substrate

TiN/AlN Nano Multilayers Film Fabricated by Plasma Enhanced Atomic Layer Deposition

Control of the initial growth in atomic layer deposition of Pt films by surface pretreatment

Influence of Surface Preparation on Atomic Layer Deposition of Pt Films

Plasma-enhanced atomic layer deposition of silicon dioxide films using plasma-activated triisopropylsilane as a precursor

(Invited) Area-Selective Atomic Layer Deposition of Manganese Oxides on Metal−Dielectric Patterns

Area-Selective Atomic Layer Deposition of TiN Using Trimethoxy(octadecyl)silane as a Passivation Layer

MOCVD of Platinum Films from (CH3)3CH3CpPt and Pt(acac)2: Nanostructure, Conformality, and Electrical Resistivity

Principle and Applications of Plasma Enhanced Atomic Layer Deposition

Effects of NH3 Plasma Pretreatment on Initial Reactions of Atomic Layer Deposition TaN Barrier Layer on SiOC Dielectric

AFM Studies of Platinum Silicide Thin Films on Silicon Grown by Pulsed Laser Deposition

Improving quality of AlN films on GaAs substrate via in-situ plasma pre-treatment in plasma enhanced atomic layer deposition

Preparation of platinum silicide films by pulsed laser deposition and pulsed laser annealing

Suppressing substrate oxidation during plasma-enhanced atomic layer deposition on semiconductor surfaces

Characterization of Al2O3 and HfO2 Grown on Metal Surfaces with Thermal and Plasma Enhanced Atomic Layer Deposition

Plasma-assisted atomic layer deposition of transition metals and their carbides

Plasma enhanced atomic layer deposition of silicon nitride using magnetized very high frequency plasma

First-Principles Predictions and in Situ Experimental Validation of Alumina Atomic Layer Deposition on Metal Surfaces

Chemistry for Positive Pattern Transfer Using Area-Selective Atomic Layer Deposition

Platinum metallization for MEMS application. Focus on coating adhesion for biomedical applications.