Abstract:The Ni-base superalloy 718 is the most widely used material for turbomachinery in the aerospace industry and land-based turbines. Although the relationship between processing and the resulting properties is well known, an understanding of the specific deformation mechanisms activated across its application temperature range is required to create more mechanistically accurate property models. Direct atomic-scale imaging observations with high angle annular dark-field scanning transmission electron microscopy, complemented by phase-field modeling informed by generalized stacking fault surface calculations using density functional theory, were employed to understand the shear process of ${\gamma}''$ and ${\gamma}'/{\gamma}''$ co-precipitates after 1 \% macroscopic strain at lower temperature (ambient and $427 °C$). Experimentally, intrinsic stacking faults were observed in the ${\gamma}''$, whereas the ${\gamma}'$ was found to exhibit anti-phase boundaries or superlattice intrinsic stacking faults. Additionally, the atomically flat ${\gamma}'/{\gamma}''$ interfaces in the co-precipitates were found to exhibit offsets after shearing, which can be used as tracers for the deformation events. Phase-field modeling shows that the developing fault-structure is dependent on the direction of the Burgers vector of the $a/2 \langle110\rangle$ matrix dislocation (or dislocation group) due to the lower crystal symmetry of the ${\gamma''}$ phase. The interplay between ${\gamma}'$ and ${\gamma}''$ phases results in unique deformation pathways of the co-precipitate and increases the shear resistance. Consistent with the experimental observations, the simulation results indicate that complex shearing mechanisms are active in the low-temperature deformation regime and that multiple $a/2 \langle110\rangle$ dislocations of non-parallel Burgers vectors may be active on the same slip plane.

Interpretation of the Habit Plane of Δ Precipitates in Superalloy Inconel 718

Shearing Mechanisms of Stacking Fault and Anti-Phase-boundary Forming Dislocation Pairs in the Γ′ Phase in Ni-based Single Crystal Superalloy

Study of pre-precipitated 8 phase promoting deformation twinning and recrystallization behavior of Inconel 718 superalloy during hot compression

A Simple Method for Calculating the Possible Habit Planes Containing One Set of Dislocations and Its Applications to Fcc/bct and Hcp/bcc Systems

In-situ Study of the Effect of Grain Boundary Misorientation on Plastic Deformation of Inconel 718 at High Temperature

Precipitation of δ phase in Inconel 718 superalloy: The role of grain boundary and plastic deformation

Shearing Mechanisms of Co-Precipitates in IN718

Dislocation Structure of Non-Habit Plane of Α Precipitates in a Ti–7.26 Wt.% Cr Alloy

Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

A TEM study of the habit plane structure of intragrainular proeutectoid α precipitates in a Ti–7.26 wt%Cr alloy

Composition and Element Distribution Mapping of γ′ and γ′′ Phases of Inconel 718 by High-Resolution Scanning Transmission Electron Microscopy and X-ray Energy-Dispersive Spectrometry

Evolution of dislocation cellular pattern in Inconel 718 alloy fabricated by laser powder-bed fusion

The Invariant Line and Precipitate Morphology in Fcc-Bcc Systems

On the Deformation Induced Heterogeneous Precipitation of Γ″ Phase in Inconel 718 Alloy

Near-coincidence-sites modeling of the edge facet dislocation structures of α precipitates in a Ti–7.26 wt.% Cr alloy

Interpretation of Precipitation Crystallography Ofmg(17)Al(12) in A Mg-Al Alloy in Terms of Singular Interfacial Structure

A New Orientation Relationship Between Cementite and Austenite and Coexistence of Pseudo-Primary and Secondary Dislocations in the Habit Plane

Coincidence structures of interfacial steps and secondary misfit dislocations in the habit plane between Widmanstätten cementite and austenite

A Molecular Dynamics Study on the Dislocation-Precipitate Interaction in a Nickel Based Superalloy During the Tensile Deformation

A comparison of dislocation cellular patterns generated in Inconel 718 alloy and pure Ni fabricated by laser powder bed fusion

Secondary Dislocation Structures in a Ni–TiN System from the GMS and O-lattice Theory