Abstract:Strain-induced precipitation was systematically investigated in austenitic Inconel 617B superalloy (IN617B) after deformation of 0.2 true strain in its service temperature range (700–850 °C). The precipitation-time-temperature (PTT) curves obtained by stress relaxation experiments showed a classic C-shape with the nose temperature of 800 °C, and a minimum incubation period of 30 s, and the main strain-induced precipitate was M23C6 carbide. After specimens deformed at 800 °C to a strain of 0.2 were held between 10 and 1000 s, they underwent a second-pass strain test, during which the M23C6 precipitates evolved and influenced the flow stress; this behavior was investigated. During the nucleation, growth, and coarsening of the strain-induced precipitates, the morphology of the M23C6 particles gradually changed from spherical to polygonal with increasing size, but the precipitates always maintained their cube-on-cube orientational relationship with the austenitic matrix. During the nucleation stage before 30 s, many pre-precipitation clusters and weak static recovery softening led to low second-deformation flow stress, which persisted at approximately 630 MPa. In the precipitation growth phase before 360 s, recovery softening balanced precipitation hardening. The strain-induced precipitates grew larger, and they were able to pin dislocations. In addition, some complex microstructures resulting from particle collisions were observed. This resulted in the maximum rate of increase of the second deformation flow stress, which quickly reached almost 700 MPa. When the holding time was extended to 1000 s, the recovery softening effect further increased, while the M23C6 particles gradually coarsened; this weakened the increasing trend of the second deformation flow stress, which increased to only 715 MPa at 1000 s

Precipitation of δ phase in Inconel 718 superalloy: The role of grain boundary and plastic deformation

Study of pre-precipitated 8 phase promoting deformation twinning and recrystallization behavior of Inconel 718 superalloy during hot compression

In-situ Study of the Effect of Grain Boundary Misorientation on Plastic Deformation of Inconel 718 at High Temperature

Delta Precipitation in Wrought Inconel 718 Alloy; the Role of Dynamic Recrystallization

On the Deformation Induced Heterogeneous Precipitation of Γ″ Phase in Inconel 718 Alloy

Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

Evaluation on static mechanical stability of wrought Inconel 718 superalloy; effect of grain configuration and δ precipitation

Simulation of δ-phase Precipitation Behavior in Hot Compression Deformation of Inconel 718 Superalloy

Effect of two-step solid solution on microstructure and δ phase precipitation of Inconel 718 alloy

Orientational growth behavior and mechanism of delta (δ) phase precipitation in cold-rolled Inconel 718 alloy during heat treatment

The effect of δ phase on the microplasticity evolution of a heat-treated nickel base superalloy

Study on the grain development and dislocation evolution from dynamic to post-dynamic stage in IN718Plus superalloy; the role of second-phase

Early evolution of δ phase and coarse γ ́ ́ phase in Inconel 718 alloy with high temperature ageing

In-situ study of adjacent grains slip transfer of Inconel 718 during tensile process at high temperature

Evolution of strain-induced precipitates in Inconel 617B alloy and their effect on flow behavior

A Molecular Dynamics Study on the Dislocation-Precipitate Interaction in a Nickel Based Superalloy During the Tensile Deformation

Improve the ductility of a nickel based superalloy by optimizing secondary phase distribution through grain boundary engineering

γʹ and γ′′ co-precipitation phenomena in directly aged Alloy 718 with high δ-phase fractions

Short Study on Mechanism of Morphology Change of γ′ Precipitates in IN718 Plus

The δ Phase Precipitation of an Inconel 718 Superalloy Fabricated by Electromagnetic Stirring Assisted Laser Solid Forming

In Situ Study of Precipitates' Effect on Grain Deformation Behavior and Mechanical Properties of S31254 Super Austenitic Stainless Steel