Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

In-situ study of adjacent grains slip transfer of Inconel 718 during tensile process at high temperature

In-situ Study of the Effect of Grain Boundary Misorientation on Plastic Deformation of Inconel 718 at High Temperature

Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

Quasi-in-situ Observation and Analysis of Grain Boundary Evolution of GH4169 Nickel-Based Superalloy During the Micro-Strain Stage of Thermal Deformation

Crystal Plasticity Modeling and Analysis for the Transition from Intergranular to Transgranular Failure in Nickel-based Alloy Inconel 740H at Elevated Temperature

In-situ SEM study of temperature-dependent tensile behavior of Inconel 718 superalloy

Study of Pre-Precipitated Δ Phase Promoting Deformation Twinning and Recrystallization Behavior of Inconel 718 Superalloy During Hot Compression

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

Quasi-in-Situ Observation and Analysis of Grain Boundary Evolution of Gh4169 Nickel-Based Superalloy During Micro-Strain Stage of Thermal Deformation

Evaluation on static mechanical stability of wrought Inconel 718 superalloy; effect of grain configuration and δ precipitation

New insights into ductility improvement of a nickel-based superalloy through grain boundary engineering

Measurement of Grain Boundary Strength of Inconel X-750 Superalloy Using In-Situ Micro-Tensile Testing Techniques in FIB/SEM System

In-situ Analysis of Slip Transfer and Heterogeneous Deformation in Tension of Mg-5.4Gd-1.8Y-1.5Zn Alloy

Tribological Behaviors and Microstructure Evolution of Inconel 718 Superalloy at Mid-High Temperature

Study on Grain Boundary Characteristic Distribution of Nickel Base 625 Alloy Controlled by Deformation Heat-Treatment Process

Precipitation of δ phase in Inconel 718 superalloy: The role of grain boundary and plastic deformation

Statistical analysis of slip transfer in Al alloy based on in-situ tensile test and high-throughput computing method

A Molecular Dynamics Study on the Dislocation-Precipitate Interaction in a Nickel Based Superalloy During the Tensile Deformation

Shearing Mechanisms of Co-Precipitates in IN718

In-situ Observation of Ni-Co Based Wrought Superalloy High-Temperature Deformation: Lattice Rotation and Grain Boundary Response

Wear mechanism, subsurface structure and nanomechanical properties of additive manufactured Inconel nickel (IN718) alloy