Abstract:Assorted morphologies of precipitates in fcc/bcc transformation systems have been reported, which often exhibit irrational characteristic. Various models have been developed to explain the habit plane (or the broad facet), but the overall morphologies of the precipitates are seldom explained quantitatively. In this work, the equilibrium cross-section of rod-shape austenite precipitates in duplex stainless steel is determined by atomistic simulation. The input orientation relationship (OR) between fcc and bcc phase is determined according to the O-line criterion (one of the interfaces contains a single set of dislocations), with the condition that the invariant line lies in close-packed plane pair of (1 (1) over bar(1) over bar)(f)|(10 (1) over bar)(b) and the Burgers vector of O-lines is [011](f|)/2|((1) over bar 11)(b)/2. The obtained OR is close to the K-S OR ((11 (1) over bar)(f)//(01 (1) over bar)(b), [101](f)//(111)(b)), with the deviation of 1.27 degrees from the parallelism in both planes and directions. Interfacial energy of interfaces in various orientations in the zone axis of the invariant line ([0.75 0.10 0.65](f)//[0.52 0.68 0.52](b)) has been calculated. To ensure the reliability of the calculated values, an initial atomic configuration free of interstitial and vacancy is constructed for each interface. The energies of the O-line interface, the interface normal to either Delta g(((1) over bar 11)) or Delta g((020)) are found to have similar values, each at a local minimum. Based on the calculated interfacial energies, the equilibrium cross-section morphology is determined by the Wulff construction. The result shows that the morphology exhibits a near rhombus cross-section, which agrees consistently with experiments. One of the major facets is the O-line interface, normal to ((0.66) over bar 0.12 0.74)(f)//((0.51) over bar (0.24) over bar 0.83)(b), in agreement with the observation. The other facet is normal to Delta g((020)) (((0.25) over bar (0.87) over bar 0.42)(f)//(0.45 (0.73) over bar 0.51)(b)) in the calculated result, while it is normal to Delta g(((1) over bar 11)) (((0.36) over bar (0.77) over bar 0.53)(f)//(0.31 (0.71) over bar 0.63)(b)) in experimental results, with about 10 degrees difference between them. The discrepancy between calculated and observed results is probably because the experiments have not reached the equilibrium state. The dislocation structures in these three interfaces are identified from the atomic simulation results by a newly developed method based on the singular value decomposition of the Nye tensor. It confirms that the O-line interface contains a single set of [011](f)/2 dislocations with spacing of 1.5 nm. The interface normal to either Delta g(((1) over bar 11)) or Delta g((020)) contains two sets of dislocations. The dislocation structure in the facet normal to Delta g((1) over bar 11)) is in good agreement with experimental observation of the non-O-line facet, including the local decomposition of dislocation core to (1 (1) over bar(1) over bar)(f) stacking faults.

A New Orientation Relationship Between Cementite and Austenite and Coexistence of Pseudo-Primary and Secondary Dislocations in the Habit Plane

Unified rationalization of the Pitsch and T–H orientation relationships between Widmanstätten cementite and austenite

Pitsch and t-h orientation relationships between widmanstatten cementite and austenite

Coincidence structures of interfacial steps and secondary misfit dislocations in the habit plane between Widmanstätten cementite and austenite

An Extended Near-Coincidence-sites Method and the Interfacial Structure of Austenite Precipitates in a Duplex Stainless Steel

A TEM Study of the Crystallography of Austenite Precipitates in a Duplex Stainless Steel

Determination of the orientation relationship between austenite and incommensurate 7M modulated martensite in Ni–Mn–Ga alloys

A Study of a New Type of Deviation from the Kurdjumov–Sachs Orientation Relationship in Face-Centered-cubic/body-centered-cubic Transformation System

An Investigation on the Equilibrium Morphology and Interfacial Structures of Pricipitates in Duplex Stainless Steel by Atomistic Simulation

Dislocation description of martensite interfaces based on misfit analysis

A new orientation relationship observed between MC and ferrite in TiMo microalloyed steel produced by ultra-fast cooling

A systematic investigation of the development of the orientation relationship in an fcc/bcc system

Direct observations of collinear dislocation interaction in a Fe-17.4 Mn-1.50 Al-0.29 C (wt.%) austenitic steel under cyclic loading by in-situ electron channelling contrast imaging and cross-correlation electron backscatter diffraction

Link between b.c.c.–f.c.c. orientation relationship and austenite morphology in CF8M stainless steel

The effect of the misfit dislocation on the in-plane shear response of the ferrite/cementite interface

A Simple Method for Calculating the Possible Habit Planes Containing One Set of Dislocations and Its Applications to Fcc/bct and Hcp/bcc Systems

A new orientation relationship OR13 and irrational interfaces between Mg2Sn phase and magnesium matrix in an aged Mg alloy

Interpretation of the Habit Plane of Δ Precipitates in Superalloy Inconel 718

A TEM study of the habit plane structure of intragrainular proeutectoid α precipitates in a Ti–7.26 wt%Cr alloy

The synergistic effect of grain boundary and grain orientation on micro-mechanical properties of austenitic stainless steel

Orientation Effect on Intergranular Fracture Behaviors along Symmetrical Tilt Grain Boundaries in Bcc Iron