Abstract:Assorted morphologies of precipitates in fcc/bcc transformation systems have been reported, which often exhibit irrational characteristic. Various models have been developed to explain the habit plane (or the broad facet), but the overall morphologies of the precipitates are seldom explained quantitatively. In this work, the equilibrium cross-section of rod-shape austenite precipitates in duplex stainless steel is determined by atomistic simulation. The input orientation relationship (OR) between fcc and bcc phase is determined according to the O-line criterion (one of the interfaces contains a single set of dislocations), with the condition that the invariant line lies in close-packed plane pair of (1 (1) over bar(1) over bar)(f)|(10 (1) over bar)(b) and the Burgers vector of O-lines is [011](f|)/2|((1) over bar 11)(b)/2. The obtained OR is close to the K-S OR ((11 (1) over bar)(f)//(01 (1) over bar)(b), [101](f)//(111)(b)), with the deviation of 1.27 degrees from the parallelism in both planes and directions. Interfacial energy of interfaces in various orientations in the zone axis of the invariant line ([0.75 0.10 0.65](f)//[0.52 0.68 0.52](b)) has been calculated. To ensure the reliability of the calculated values, an initial atomic configuration free of interstitial and vacancy is constructed for each interface. The energies of the O-line interface, the interface normal to either Delta g(((1) over bar 11)) or Delta g((020)) are found to have similar values, each at a local minimum. Based on the calculated interfacial energies, the equilibrium cross-section morphology is determined by the Wulff construction. The result shows that the morphology exhibits a near rhombus cross-section, which agrees consistently with experiments. One of the major facets is the O-line interface, normal to ((0.66) over bar 0.12 0.74)(f)//((0.51) over bar (0.24) over bar 0.83)(b), in agreement with the observation. The other facet is normal to Delta g((020)) (((0.25) over bar (0.87) over bar 0.42)(f)//(0.45 (0.73) over bar 0.51)(b)) in the calculated result, while it is normal to Delta g(((1) over bar 11)) (((0.36) over bar (0.77) over bar 0.53)(f)//(0.31 (0.71) over bar 0.63)(b)) in experimental results, with about 10 degrees difference between them. The discrepancy between calculated and observed results is probably because the experiments have not reached the equilibrium state. The dislocation structures in these three interfaces are identified from the atomic simulation results by a newly developed method based on the singular value decomposition of the Nye tensor. It confirms that the O-line interface contains a single set of [011](f)/2 dislocations with spacing of 1.5 nm. The interface normal to either Delta g(((1) over bar 11)) or Delta g((020)) contains two sets of dislocations. The dislocation structure in the facet normal to Delta g((1) over bar 11)) is in good agreement with experimental observation of the non-O-line facet, including the local decomposition of dislocation core to (1 (1) over bar(1) over bar)(f) stacking faults.

A TEM Study of the Crystallography of Austenite Precipitates in a Duplex Stainless Steel

A TEM Study of the Crystallography of Lath-Shaped Austenite Precipitates in a Duplex Stainless Steel

An Extended Near-Coincidence-sites Method and the Interfacial Structure of Austenite Precipitates in a Duplex Stainless Steel

An Investigation on the Equilibrium Morphology and Interfacial Structures of Pricipitates in Duplex Stainless Steel by Atomistic Simulation

Determination of precise orientation relationships between surface precipitates and matrix in a duplex stainless steel

Double Diffraction or ω-Fe Diffraction in Body-Centered Cubic {112}<111>-Type Twinned Martensite

Link between b.c.c.–f.c.c. orientation relationship and austenite morphology in CF8M stainless steel

In Situ TEM Study on the Sympathetic Nucleation of Austenite Precipitates

New insights into the character of austenite-ferrite boundaries in an additively manufactured duplex stainless steel

Double Diffraction or -Fe Diffraction in Body-Centered Cubic {112}?111?-Type Twinned Martensite

Crystallography of Surface Precipitates in a Duplex Stainless Steel

In-situ TEM study of dislocation emission associated with austenite growth

Invariant Deformation Element Model Interpretation to the Crystallography of Diffusional Body-Centered-Cube to Face-Centered-Cube Phase Transformations

A General Crystallographic Model of Fcc/Bcc(Bct) Martensitic Nucleation and Growth in Steels

Ferrite-austenite synergistic deformation behavior in a 2205 duplex stainless steel containing equiaxed austenite domains

Dissecting the Mechanism of Martensitic Transformation Via Atomic-Scale Observations

Direct Observations on the Crystal Structure Evolution of Nano Cu-Precipitates in an Extremely Low Carbon Steel

In-situ study on the coordinated deformation mechanism of austenitic stainless steel with mixed crystal degree

Microstructure evolution in 439 stainless steels under tensile: phase field simulation and experiment

Characterization of Nano-Sized Precipitation and Dislocations and the Correlation with Mechanical Properties of a Low Alloy TRIP-aided Steel

Dislocation Activities at the Martensite Phase Transformation Interface in Metastable Austenitic Stainless Steel: An In-situ TEM Study