Abstract:This study investigated the effect of grain size distribution on the deformation behavior in fine-grained (FG) austenitic stainless steels (γ-SSs). Commercial Cr–Mn–N γ-SS was selected as the coarse-grained (CG) specimen, which was cold rolled and then annealed at 1000 °C for 60 s and 700 °C for 3600 s to obtain FG specimens with similar grain sizes but different grain size distributions. The CG specimens annealed at 1000 °C for 60 s and 700 °C for 3600 s were referred to as unimodal-FG and bimodal-FG specimens, respectively. The tensile properties revealed that the yield strength was enhanced from 383 MPa to 685 MPa when the grain size was refined from CG (10.7 μm) to FG (∼1.8 μm). Moreover, the bimodal-FG specimen exhibited a higher total elongation of 48% than 36.5% for the unimodal-FG specimen. Transmission electron microscopy, electron backscatter diffraction and X-ray diffraction were used to identify the microstructural characteristics during tension. The results indicated that the main deformation mechanisms of γ-SSs specimens during tension were dislocation generation and accumulation at the initial stage, deformation twinning at the intermediate stage, and deformation-induced martensite (DIM) at the final stage. Compared with the unimodal-CG counterpart, grain refinement in the unimodal-FG specimens restricted the formation of DIM due to the increased austenite stability. A newly discovered phenomenon was that the bimodal-FG specimens promoted the formation of geometrically necessary dislocation (GND) and DIM compared to the unimodal-FG, which was due to the uneven deformation in grains located on hetero-boundaries (HBs). Moreover, the bimodal-FG specimen was preferentially formed DIM on HBs, especially in the smaller grains side rather than inside larger grains due to the higher stress concentration in smaller grains.

Tensile behavior of ferritic/austenitic iron with a bimodal structure:An atomistic study

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Prediction of Mechanical Properties in Bimodal Nanotwinned Metals with a Composite Structure

Microstructures-based Constitutive Analysis for Mechanical Properties of Gradient-Nanostructured 304 Stainless Steels

Numerical investigation of fracture behavior of nanostructured Cu with bimodal grain size distribution

Microstructure‐Property Relations in the Tensile Behavior of Bimodal Nanostructured Metals

Micromechanical Simulation of Fracture Behavior of Nanostructured Metals with Bimodal Grain Size Distribution

Modeling Grain Size Dependent Optimal Twin Spacing for Achieving Ultimate High Strength and Related High Ductility in Nanotwinned Metals

Modelling the Plastic Deformation of Nanostructured Metals with Bimodal Grain Size Distribution

Strong size effect on deformation twin-mediated plasticity in body-centered-cubic iron

Probing the impact of grain size distribution on the deformation behavior in fine-grained austenitic stainless steel: A critical analysis of unimodal structure versus bimodal structure

Deformation Mechanism of Bimodal Structured 2205 Duplex Stainless Steel in Two Yield Stages

Microstructure evolution in 439 stainless steels under tensile: phase field simulation and experiment

Unusual grain-size effects on tensile deformation behavior of twinning-induced plasticity steel with low Mn content

Ferrite-austenite synergistic deformation behavior in a 2205 duplex stainless steel containing equiaxed austenite domains

Tensile Properties and Microstructure Evolutions of Low-Density Duplex Fe–12Mn–7Al–0.2C–0.6Si Steel

Micromechanism involved in ultrafine grained ferrite/martensite dual phase steels strengthened by nanoscale Cu-rich precipitates

Micromechanical Observation and Numerical Simulation for Local Deformation Evolution of Duplex Stainless Steel

Study on the factors influencing the mechanical properties of bimodal nanotwinned Cu-Ag alloys

Effect of Strain Localization on the Mechanical Properties from Nonuniform Grain Size Distribution of Ultralow Carbon Steel

Effect of Grain Size on the Plastic Deformation Behaviors of a Fe-18Mn-1.3Al-0.6C Austenitic Steel