Abstract:This study investigated the effect of grain size distribution on the deformation behavior in fine-grained (FG) austenitic stainless steels (γ-SSs). Commercial Cr–Mn–N γ-SS was selected as the coarse-grained (CG) specimen, which was cold rolled and then annealed at 1000 °C for 60 s and 700 °C for 3600 s to obtain FG specimens with similar grain sizes but different grain size distributions. The CG specimens annealed at 1000 °C for 60 s and 700 °C for 3600 s were referred to as unimodal-FG and bimodal-FG specimens, respectively. The tensile properties revealed that the yield strength was enhanced from 383 MPa to 685 MPa when the grain size was refined from CG (10.7 μm) to FG (∼1.8 μm). Moreover, the bimodal-FG specimen exhibited a higher total elongation of 48% than 36.5% for the unimodal-FG specimen. Transmission electron microscopy, electron backscatter diffraction and X-ray diffraction were used to identify the microstructural characteristics during tension. The results indicated that the main deformation mechanisms of γ-SSs specimens during tension were dislocation generation and accumulation at the initial stage, deformation twinning at the intermediate stage, and deformation-induced martensite (DIM) at the final stage. Compared with the unimodal-CG counterpart, grain refinement in the unimodal-FG specimens restricted the formation of DIM due to the increased austenite stability. A newly discovered phenomenon was that the bimodal-FG specimens promoted the formation of geometrically necessary dislocation (GND) and DIM compared to the unimodal-FG, which was due to the uneven deformation in grains located on hetero-boundaries (HBs). Moreover, the bimodal-FG specimen was preferentially formed DIM on HBs, especially in the smaller grains side rather than inside larger grains due to the higher stress concentration in smaller grains.

Effect of Strain Localization on the Mechanical Properties from Nonuniform Grain Size Distribution of Ultralow Carbon Steel

Modelling the Plastic Deformation of Nanostructured Metals with Bimodal Grain Size Distribution

Numerical investigation of fracture behavior of nanostructured Cu with bimodal grain size distribution

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Micromechanical Simulation of Fracture Behavior of Nanostructured Metals with Bimodal Grain Size Distribution

Microstructure‐Property Relations in the Tensile Behavior of Bimodal Nanostructured Metals

The Direct and Indirect Effects of Nanotwin Volume Fraction on the Strength and Ductility of Coarse-Grained Metals

A statistical model for predicting the mechanical properties of nanostructured metals with bimodal grain size distribution

Prediction of Mechanical Properties in Bimodal Nanotwinned Metals with a Composite Structure

Numerical simulation of ballistic performance of bimodal nanostructured metals

Micromechanical simulation of fracture behavior of bimodal nanostructured metals

Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

Probing the impact of grain size distribution on the deformation behavior in fine-grained austenitic stainless steel: A critical analysis of unimodal structure versus bimodal structure

Effect of Grain Size on the Plastic Deformation Behaviors of a Fe-18Mn-1.3Al-0.6C Austenitic Steel

Local Deformation Mechanisms in Metal Systems with a Tailored Grain Size Distribution

Grain size gradient effect on grain boundary mediated deformation of nano-grained metals

Activating dispersed strain bands in tensioned nanostructure layer for high ductility: The effects of microstructure inhomogeneity

Enhanced strain hardening by bimodal grain structure in carbon nanotube reinforced Al–Mg composites

Unusual grain-size effects on tensile deformation behavior of twinning-induced plasticity steel with low Mn content

Tensile behavior of ferritic/austenitic iron with a bimodal structure:An atomistic study

Effect of compositional heterogeneity on the mechanical properties of a single-phase Cu-9Al alloy with different grain sizes