Abstract:Large volume cubic press is one of the most popular high pressure devices which can produce pressures up to about 7 GPa. It is well known experimentally that the enhancing of the maximum pressure generated in the large volume cubic press has attracted wide attention among scientists and engineers because the higher pressure is capable of synthesizing some materials with interesting properties. In the large volume cubic press, pyrophyllite is typically used as a pressure-transmitting medium. A specimen immersed in such a solid experiences a generalized stress state. The pressure distribution in pyrophyllite is an important parameter for characterizing the sample environment and designing the experiments at high pressure. There is a need for the quantitative measurement of pressure gradients in the pyrophyllite pressure medium, so that the accurate experimental data under high pressure can be obtained. In the large volume cubic apparatus (68 MN), we put a circuit into the high pressure cubic cell, so that the pressures at various positions can be measured by using the phase transitions in Bi, Tl and Ba. In the present work, the relationship between the total press load and the press load allocated to the anvil face, and the relationship between the total press load and the press load allocated to gaskets are established at room temperature. The results show that with the increase of the total press load, the load allocated to the gaskets is increased sharply, while the curve of load allocated to the anvil face versus total press load reaches a plateau, which results in the cell pressure reaching upper limit when the cell pressure reaches up to about 5 GPa. According to the experimental results, the stress state of the cubic cell under high pressure is analyzed and the reason why the pressure generated in the large volume cubic chamber is difficult to exceed 7 GPa is explained. Based on the geometrical structure of the cubic cell, the scheme to increase the upper pressure limit for cubic cell by using the material with high bulk modulus as the pressure transmitting medium and the material with low bulk modulus as the gasket, is proposed. Additionally, the method of calculating the pressure values at different positions along the axis of symmetry in the cubic cell is given through the quantitative calibration of the pressure gradient in the axial direction of the cubic cell. This method can provide more accurate pressure data for high pressure experiments.

Estimation of Stress Distribution of Pressure Media in a Flat Belt Type High Pressure Apparatus by the Rigid Plastic Method

Analysis of Controllable Stress Distribution and Optimal Design of Flat Steel Ribbon Wound Pressure Vessel

CONTROLLABLE STRESS ANALYSIS AND DESIGN OF FLAT STEEL RIBBON WOUND PRESSURE VESSEL

Force Analysis and Pressure Quantitative Measurement for the High Pressure Cubic Cell

Optimal Winding Conditions of Flat Steel Ribbon Wound Pressure Vessels with Controllable Stresses

Mechanical Analysis of Carbon Fiber Wound High Pressure Hydrogen Storage Vessel and Prestress Control in Manufacturing Process

Radial Displacement Measurement of Hydrogen Storage Cylinders under Internal Pressure Based on Fringe Projection Profilometry

Finite Element Analysis for the High Pressure Rotary Cylinder Block

A Simplified Method for Calculating the Stress of a Large Storage Tank Wall

Theoretical Assessment of Burst Failure of Internally Pressurized Defect-Free Pipelines with Plastic Anisotropy

Centrifuge Experiment and Numerical Analysis of an Air-Backed Plate Subjected to Underwater Shock Loading

Plasticity Correction on Stress Intensity Factor Evaluation for Underclad Cracks in Reactor Pressure Vessels

Study on Solving Contact Stress on the Blade Rabbet

Investigation on the Plasticity Correction of Stress Intensity Factor Calculations for Underclad Cracks in Reactor Vessels

Stress analysis of a thick-walled cylinder composed of incompressible hyperelastic materials subjected to internal and/or external pressure: analytical and finite element analysis

Nonlinear Failure Analysis on Pressurized Cylindrical Shell Using Finite Element Method: Comparison of Theoretical and Experimental Data

Proposal of Method for Estimating Clothing Pressure of Tight-Fitting Garment Made from Highly Elastic Materials: Hybrid Method Using Apparel CAD and Finite Element Analysis Software

Apparatus for material tests using an internal loading system in high-pressure gas at room temperature

Pressure Container Surface Crack Analysis

Pressure distribution analysis of fiber reinforced plastic components made by rubber pressure moulding technique

Effects of Plasticity on the Stress Intensity Factor Evaluation for Underclad Crack under Pressurized Thermal Shock Events